Recent content by backmd
-
B
1980 FM tuner dead
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L...- backmd
- Post #91
- Forum: Pioneer Audio
-
B
Rebuilding/Upgrading the 2000x
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L...- backmd
- Post #44
- Forum: Exclusively Sansui
-
B
Marantz 150 tuner ferrite slugs
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L...- backmd
- Post #29
- Forum: Marantz Audio
-
B
Where can I find a am IF transformer for a 490-T.part number ZZ2984?
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L... -
B
Where can I find a am IF transformer for a 490-T.part number ZZ2984?
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L... -
B
Sansui 210 Receiver Alignment
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L... -
B
MX113 problem in FM stereo mode
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L...- backmd
- Post #15
- Forum: McIntosh Audio
-
B
Rebuilding/Upgrading the 2000x
The below is from a Sherwood S2300 broken slug repair: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L...- backmd
- Post #43
- Forum: Exclusively Sansui
-
B
Marantz 150 tuner ferrite slugs
So the below is from a Sherwood S2300 with a broken slug: Working on T3 we tried the alignment tools, then the steel metal tools, then WD40, then baby powder, then PB blaster, hair dryer and finally the jewelers screwdriver between the slug and outer coil. Now it really is time for the reverse L...- backmd
- Post #28
- Forum: Marantz Audio
-
B
Yaggi antenna not that great ...whats the problem??
Aint that the truth, just replace everything and it will work! -
B
Yaggi antenna not that great ...whats the problem??
Sounds real good with the Accuphase T109V on classical and jazz! -
B
Yaggi antenna not that great ...whats the problem??
Retrospectively the main conductor failed that carries the signal. With a Fluke multimeter this copper conductor measured infinity! -
B
Yaggi antenna not that great ...whats the problem??
Aha the antenna finally failed and the only thing that was not replaced was the 100 ft. RG6 coaxial line which was 18 years old. Everything comes in just fine now. Very very happy now! -
B
At-home FM transmitter for personal use --anyone try it?
5 watts and a good antenna goes 6 miles but I would not dare to transmit more than 15 minutes since the FCC knew the guy who sold me electronics surplus material. Plus the signal had 60 cycle hum, but it was fun for 15 minutes