Oldsansui441's Recent Activity

  1. Oldsansui441 liked Bratwurst7s's post in the thread Yamaha M-70 Thread.

    So setting the power output indicator LED's wasn't so hard. I had already bought a 75 ohm BNC->RCA cable so hooking up my frequency...

    DSC05525.jpg DSC05526.jpg DSC05527.jpg Jun 23, 2018 at 7:54 AM
  2. Oldsansui441 replied to the thread Yamaha M-70 Thread.

    Nice job, looks like you have a great setup.

    Jun 23, 2018 at 7:53 AM
  3. Oldsansui441 liked canuckaudiog's post in the thread Speaker Recap - Electrolytic or Film?.

    @corbin What you've said strikes right at the heart of the issue with replacing capacitors in a crossover - the ESR properties....

    Jun 22, 2018 at 8:39 PM
  4. Oldsansui441 liked Bratwurst7s's post in the thread Yamaha M-70 Thread.

    So I finally replaced the trim-pots for the meter (1k ohm) and ZDR (500 ohm) adjust, Bourns 3296Y-1-102LF and 3296Y-1-501LF...

    DSC05516.jpg DSC05518.jpg DSC05519.jpg DSC05521.jpg DSC05524.jpg Jun 22, 2018 at 8:26 PM
  5. Oldsansui441 replied to the thread Pioneer SX-1050 brought up from the depths....

    Always thought Pioneer's had pretty good anodizing :rolleyes:. Yes for sure, they are very time consuming. I think l put about 30-40...

    Jun 21, 2018 at 9:02 PM
  6. Oldsansui441 replied to the thread Yamaha CA-2010 possible restoration.

    No worries.

    Jun 21, 2018 at 6:30 PM
  7. Oldsansui441 liked kevzep's post in the thread SX1010 Is it the pinnacle of Pioneers Receiver engineering? Maybe it is!!.

    Never too late to the party!! I like the pushbutton switches, I am not sure why people don't like them, the unit look sleek, less levers...

    Jun 21, 2018 at 6:28 PM
  8. Oldsansui441 replied to the thread Yamaha CA-2010 possible restoration.

    These are the relays that l used, cheers. https://au.mouser.com/ProductDetail/769-HL2-HP-DC12V-F

    Jun 21, 2018 at 5:35 PM
  9. Oldsansui441 liked AngelAT's post in the thread Marantz 2238 Black with light diodes?.

    Thanks for the replies! I went for the diy procedure and now things are looking much better! I also added velum and the look is as it...

    IMG_20180621_180917.jpg IMG_20180621_190554.jpg Jun 21, 2018 at 5:14 PM
  10. Oldsansui441 liked Pearlybaker's post in the thread Advice needed on acquisition of SX-1010.

    Speakers cabinets have small initials carved into the top - I don’t think it went through veneer. I was going to try to “reinflate” the...

    Jun 20, 2018 at 5:12 PM
  11. Oldsansui441 liked larryderouin's post in the thread Advice needed on acquisition of SX-1010.

    For a PIONEER nut, a 1010 is a right of passage so to speak. A Pioneer nut who hasn't owned and marveled at a 1010 don't know Jack...

    Jun 20, 2018 at 5:11 PM
  12. Oldsansui441 replied to the thread Advice needed on acquisition of SX-1010.

    Wow, those pieces are in fantastic shape, nice find. As you say those shipping plugs would have to be ultra rare to see these days.

    Jun 19, 2018 at 11:56 PM
  13. Oldsansui441 replied to the thread Project: Technics SA-800.

    Nice work Super Noob, she should now be good for many more years of listening pleasure :thumbsup:.

    Jun 19, 2018 at 9:24 AM
  14. Oldsansui441 replied to the thread HELP! Diode identification.

    Did you get a chance to try what Hyperion suggested and check DC on the right channel whilst inducing the problem?

    Jun 19, 2018 at 9:00 AM
  15. Oldsansui441 replied to the thread SX-939 & SX-9930 Summer Project.

    Use a 1mm drill to enlarge the holes in the board to suit the new KSC3503dstu's. Drill from the trace side. They will come up great in...

    Jun 19, 2018 at 5:56 AM