Recent content by pakko

  1. pakko

    Sanyo TP 1000 Spinning Way To Fast

    Hey, Hey - did you solve the speed problem….. I have the same on my one here and try to find a solution. Was the recap successful?
  2. pakko

    Help with a Yamaha PX-2 turntable

    Here the solution for the Automatic issue on all PX-2 or PX-3: https://www.audiokarma.org/forums/index.php?threads/a-little-help-with-my-yamaha-px2-please.308044/page-2#post-15900716
  3. pakko

    Yamaha PX-2: need ideas for fixing problems

    Everybody can find the solution here in this thread : https://www.audiokarma.org/forums/index.php?threads/a-little-help-with-my-yamaha-px2-please.308044/page-2#post-15900716 Worked perfect and ready in 30 min!
  4. pakko

    A little help with my Yamaha PX2, please

    I didn't tried that. Wanted to be as close as possible to the original layout.
  5. pakko

    A little help with my Yamaha PX2, please

    Here is the solution for all of you who still looking for an easy fix for the Yamaha PX-2 (PX-3) After reading all the informations here in this forum and others I tried this and it worked perfectly: The best match for the not working sensors (SPI-201) are Omron EE-SX298 - these are not...
  6. pakko

    Luxman SQ-202 phono section

    I just finished this rare Luxman SQ-202 early solid state amp with a fully recap. It works great and just needs a little fine tuning with some adjustments. I do have a service manual but there are no further informations about the adjustments. There are four trimmer in on the phono board. Two...
  7. pakko

    Scott 312-D Tuner - need help!

    To finish this story here... the Scott Tuner is back to life. Thank you Tom B for the tip with the Testing Cap I could figure out than IC 304 was bad. Because I couldn't find exactly this part I ordered a LM703LH wich is working very good in this position. You need to cut of two unused legs...
  8. pakko

    Scott 312-D Tuner - need help!

    Thanks everybody. After testing the ICs it looks like IC304 is not OK - so I ordered a new one and will report!
  9. pakko

    Scott 312-D Tuner - need help!

    Thank you very much. I´ll gonna check the IC´s first and let you know. With a signal follower I can trace the signal up to the input pins of T304. nothing on the outputs (pins 3,4,6) Can this discriminator be broken or just out of alignment? How can I check T304?
  10. pakko

    Scott 312-D Tuner - need help!

    Hey everybody! I got a nice Tuner from Scott. Model Stereomaster 312-D. Not playing (no output) at the moment. I could track the problem back to the FM IF Amplifier board. Here the sound disappears after the output of IC304 in T304 . So, it seems to me than this part T304 is the problem...
  11. pakko

    Accuphase P-300 DC offset way to high

    OK - DC offset and Bias are adjustable now... good!
  12. pakko

    Accuphase P-300 DC offset way to high

    OK - I found a faulty transistor on the power supply board. Q3 was down and I replaced it. Now the output on the +-70V rail is OK (connect 2 and 9) but the +-25V is still to high. It is by 33V at the moment (connect 4 and 6) - should be +-25V What do you think...?
  13. pakko

    Accuphase P-300 DC offset way to high

    I thought the same at this point. The relays is pretty tuff on this amp. I gonna check on advise!
  14. pakko

    Accuphase P-300 DC offset way to high

    I gonna do this and see if everything is OK on the power supply board! Let you know...
  15. pakko

    Accuphase P-300 DC offset way to high

    As source I used an iPod if this is the question...
Back
Top Bottom