Search results

Reping Shorewood, mn. As others have said, Aaron and Ron carried the weight on TC get-togethers for years. Good times, I still have the T-shirts. I've been awy from building, collecting, posting on AK, etc. I can blame some of that on health issues. Still blasting music but a minor stroke...

Since meters are using very low current and all are not perfectly aligned with each other, minute input changes will nearly always cause indicator misalignment with verified amp output. If it was me, I'd lower the brim on my "paint-by-numbers cap" and enjoy the music. If it bothers you to...

Crackling, interuptions, no volume are known problems with Kenwood pieces from that era. The issue usually lies in the volume pot. Search and read about the use of Caig De-Oxit on this forum. Faderlube is good stuff, too, but Deoxit will probably clean up more oxidation. I have a Kenwood...

Restore them. They are well regarded.

I bet they sound great. How do you have them stuffed? I need to get back into my MLTL's and remove some fiberglass to let the woofer sound a bit better (15" Altec). I have some Fostex single drivers in complex horns that really become transmission lines when in use. No stuffing used except for...

That's just me, a funny, itch-scratching guy all the way! :bigok: The Coral is a good choice.I had/have a pair around here at one point. I need to clean shelves and see what I actually have, ahhhh. :dunno:

I'd suggest looking for a pair of vintage JBL Studio Monitors/Studio Control Monitors. They will project a clean sound in that space, have enough bass for most folks (add subwoofers for chest pumping since giving up the CV's will be a chore). Really nice work. Hope you follow up with a...

Right now, I'm listening to Royksopp, "Running to the Sea" in my garage/shop using single Fostex Sigma 108's in a simple reflex box. IIRC, the boxes were done in an afternoon. Box is BB plywood, holes cut on the drill press using hole saws. Started using these again and the sound is immersive...

I ran into a guy that had a different MO on hoarding. I sold him an older Sansui tuner/amp and he told me where it was destined, to a friend that could use it. He had done this many times with some decent vintage gear. The recipient was pledged not to sell and he was able to enjoy his hoard as...

Wire removal is as stated or a cut and resolder works, too. I'd suggest to do some research and see if you really need the contact plate and selector to route power through the various resistors. Once voiced correctly for your room, it typically can be bypassed through one value of resistor.

DTR research, Denver Colorado trademark first used in commerce 1974...

The bearing in the B12 is a shaft with a single ball atop it. I would remove the platter. make sure the ball is secured so it won't go missing (tape the platter tube),and wrap the platter separate from the deck. That way, if the table is impacted or spends time on an angle, the platter shaft...

Lol, the most applicable statement so far! The values stated for the fuses are in the realm of most solid state amplifiers. They should do an adequate job to protect the equipment and the user's environment. It is about how to protect the path of power in the amplifier.

It's probable that the function switch is not the actual path of power to the tuner lamps. The power is probable to come from the circuit board. I say probable because I don't have the QRX-5500 service manual or schematics in hand. You can visit Hifi Engine and see if a free download is...

Possibly an old kit speaker. The woofer may be a coaxial/triaxial. There are an extra set of wires from the crossover box and that was probably for adding a horn (based on the square baffle cutouts). Best ID involves numbers off the woofer (EIA xxx-xxx) or inspection for a mfg's number. The...

Most discrete component audio gear built in the vintage era is repairable if you have diagnostic experience, a schematic, and know where to source the readily available parts. In that sense, I would vote for some of the Accuphase gear since the layout didn't scrimp on board territory and most of...

Attaboy, a guys' gotta' know what his gear is capable of. I hope you took the time to play some riffs that worked well with the echo, that could have made a good track. Much sweeter if a bird, possum, or a neighbor's dog chimes in. I have two Marshall 4x stacks and a 100W double head. I need to...

FWIW, anything auto related, my first step is to check all grounds to be sure there is good continuity. A bad ground seems far fetched for a signal popping issues but stranger things have happened. Is your Taurus headunit still powered by the factory wiring? A diagnostic experiment may be to...

canuck, About the bracing: Add your bracing in where possible and where needed. Those enclosures were built correctly and with durability in mind since the builder was a furniture maker. He used his skills and procedures to build a box and that is a good thing. As Bowtie remarks, small...

I love me some boomboxes!:rockon: I built a wooden enclosure for the Daughter. She strapped it onto her "Parade Bike" and used it to advertise for her radio station. 7" speakers and enclosures stuffed to some crazy specification/mind-spaghetti level. I have a design for an Aluminum "high tech"...

I occasionally mess with the garage system. I use smaller speakers mounted on brackets. The cabinet tops are within 6" of the ceiling. I'd bet those JBL Century's would really peak the bass if mounted close to the ceiling. The ceiling provides a an additional surface for dispersion. If you make...

I've found the greatest difference between irons is how it fits the hand and is adequate for the work involved. Hakko make good irons but I bet JBC is good, too.

"Anyway this is why I don't respond to finishing threads much anymore on the site. Can't give professional advice without friction form others that don't do this for a living." Hey, everyone has different ideas. That doesn't make them bad, just different. Yes, applying poly with 1500 paper does...

Are any of those Maggie's, field coil? My 1949 console has two Gold Lion field coils. They dig fairly deep and are like butter going up the register.

A well regarded fella' that has worked on Altec for years told me to use closet hanger rod. Cut the rod to have a low friction fit from panel to panel, glue the ends, and install. The last big cabs I built, had a windowpane front to back, and three horizontal braces from each side to the...