Search results

I have a 3d printer and have made some fine detail parts. I make my own M4 fine thread .75 pitch screws and nuts for my PCB on my crossovers.

Thanks Mark, just finished putting in new belts and the rebuilt clutch.Works Great!!

Mark I have a clutch I would like to have you rebuild. I just removed the clutch and arm from a CT-F8282. For some reason I cant seem to PM you.

FM sounds great!! More so on the reception. Further away stations are coming in clearer.

I'm sorry rcs16...Thanks for the help with the tuner board. You guys are awesome!!

Ive been busy lately, and some of the kids came home for a visit. They left this morning so I had time to recap the tuner board. Thanks to your advice 1MEGO it was pretty straight forward. I picked up a Jonard tool to take the wire wraps off and I was able to rewrap all of them but 1. Just have...

I placed my order.

Thanks rcs16!!! So after 3 hours of trying to look for replacement transistors, Q10 is the only one I got right? I'm terrible at searching for replacement components. is this ok for C62?https://www.mouser.com/ProductDetail/WIMA/MKS2C031001A00KSSD?qs=sGAEpiMZZMv1cc3ydrPrFwgzP98AO9idyI15Dd5SyS0=...

OK 1MEGO I'm going to go ahead with the tuner board. I spent a lot of time picking out the parts to put my order in with Mouser. Here is a list of what I came up with. Let me know if there is anything else I should put on the order.Many of the parts I have from previous orders. C25 4.7, 16V CEA...

finished up on the power amp today and sounds great. I believe all I have left is replacing some lights. The lights that are burnt out is the speaker A and B, Aux, and 2-8v 0.3 amp bulbs. The only board I haven't worked on is the tuner board. I'm guessing nobody likes to mess with this board.

It turned out to be the volume pot ACV-164. After using Deoxit many times the buzzing has stopped.

The receiver is working again.sort of. I hooked the speakers up to speaker terminal A and got a 120hz humm/buzzing noise, you cant hear it with the radio turned up, but when you turn the volume all the way down is when its quite noticeable. I switched the speakers to speaker terminal B and the...

I pulled and tested almost all of the components today and everything tested ok. I decided to look at the transistors to see if I installed them wrong. They were all installed right. And then I noticed Q3 and Q4 were not the same transistor as I saw on the schematics.I changed it out with the...

I made a mistake. I listed my readings as BEC and should have listed as BCE. I went back and changed it.Sorry.

Here are the transistor measurements BCE Q1 .008, 8.35, -.005 Q2 .003, 8.37, -.017 Q3 0, 36.50, -.806 Q4 -.011, 7.94, -.630 Q5 8.46, .625, 9.09 Q6 .625, .004, 0 Q7 .004, 36.66, 0

I did the Bias today and I built a dim light tester as well. Sadly still no click of the relay yet. The new readings on the AWM-062 protection board is: 1. 0 2. -12.83 3. 0 4. 0 5. -.01 6. 0 7. 0 8. -.01 9.36.69 10.36.56 11.36.56 12. 7.91 AC

I can do that. I briefly read through it . I'll look into it tomorrow. What do you think about the measurements I took? Do you still think Amp adjustments should be the next step?

AWM-062 1..030 2.-12.70 3..025 4.0 5..024 6..038 7..030 8..015 9.36.48 10.36.5 11.36.51 12..7.89AC

I'll post the pin measurements of the protection board, then i need to get something to eat. :)

Relay isnt kicking in. I was going to check the protection circuit next.I'll put that off until tomorrow. I've been on this since 7:00 this morning.

Sweet!!! Thanks 1mego!! Wish you were closer i would take you out for a steak dinner.

13. -12.91 14. -49.52 15. -17.41

................B............C..........E Q2 - 50.13.......-67.6......-49.54 Q4 -13.45........-50.16.....-12.93 Q6 -19.91.......-44.32......--17.44

The new zener brought voltage down to 12.74 on Q4 emitter. Thats odd, the old one tests ok. Oh well

I'll change it out with a new one. Glad I bought a kit so i would have plenty to spare.