Search results

Thank you.Ill look Mark up.

I have a nice Harmony remote i can use.. This is a great suggestion, and thank you! I think I owe it to this site to subscribe, so that's coming up. Are there alternatives to the CR7 that could be considered as well?

Looking for some advice on the best way to get my MX 114 Tuner Preamp singing clearly again.. The Volume pot like many older units is worn, and isn't accurate until above 11oclock on the dial. I have flushed and exercised t with Deoxit, but no luck. Im hoping someone might know of a viable...

Good morning to the Experts. I'm looking for some speaker surrounds for a pair of MDM-4 monitors. These are installed Inverted. I ordered a single to test fit, and it was great Except it doesn't quite fit the cone. Just a little to wide. This is what i have now PN= 610-612-1 ID = 4-1/4 OD...

I believed that screw to be an antiskate, but you could be correct. I'll experiment today..

GD, Is there an adjustment to the Lead IN on this table that you are aware of? I just got one NIB, but suffering from a looong storage. Thanks!

I'm trying to locate the correct Caps for an RSb project. 75 mfd, 100v non polar. Not having much luck though. Any suggestions would be very appreciated. Thanks!

I'm going to take a shot here at understanding a bit more about matching the MCM woofers currently in the Jr's until i can find a more suitable replacement or originals. Firstly, Thank you swechsler for the basic education that's surely going to make my life much more difficult, but more...

Hello all. I'm new to Infinity, but not new to nice speakers. I just picked up a pair of Q Jr's ( inexpensive) and have a few questions. Firstly, the Woofers have been replaced with an 8 OHM MCM Audio dual VC 55-1465. Is this an appropriate replacement or were the originals a 4 ohm...

Just got this interesting deck, and it works but shuts off shortly after pressing play. I believe it's the Counter belt broken. I can see 2 of the belts clearly, but the counter belt is behind all the circuitry. Looking for a manual or Belt sizes if i can find them. Thanks!

Lol.. That must be it. Internet sleuthing hasn't turned up anything better.

This might be a good question for this thread. Any clue as to what this is or does?

I had to repair 1 Woofer tear, and Re-glue the cones to the Basket with E6000. That all worked great. Mid's are " Wrinkled" presumably because they stuff insulation into the enclosure, but no rips or issues. I read this is common. No Negative sound effects. Pot's needed to be cleaned, but were...

I've been looking on the Web at how to coat unfinished Pine, and ill take the challenge I think. Worst case, Ill have to Veneer them, Best case, They might look at least original enough to be interesting. Now if I can locate that other Pin on A Badge for one of the grills, Ill have saved a nice...

They are definitely Plywood. 1'st and 2'nd pictures are the same speaker. both looked like the 1'st before i stripped them. I'm hoping a good sanding and varnish will be all that's needed to make them acceptable. I've done the work to get them sounding great, but i have limited refinishing...

Pine it is then. No wonder they tried to paint it. Maybe i can get them presentable by conditioning the wood and poly-ing them. Thanks!

Quick question.. I have a pair of AR 2A's i just recapped, Resealed, and they sound great. I started to strip off some terrible White Paint, and when I'm finished, id like to either Stain or Poly the cabinets. Anyone have a guess as to what wood grain this is? I thought Birch, but maybe pine...

USPS is completely incompetent. Ordered Roy C's surround dope and stated it was delivered yesterday. Sure enough, nothing in the box. Ill be getting a start on the re-build tonight with the 4, and 6 uf caps ordered. Totally pissed about this though.. Cant just run to the hardware store and get...

A Face only a mother could love here..I got these AR's and a set of Strange Electrostatic Realistic as well as a few Pinnacle, KLH, Boston sets. I ordered the Clear Tacky glue to attach. Thanks!

That Pliobond looks interesting but i can't find it locally. I will wait for Roy's product to seal the surrounds for sure. I couldn't locate it on his Auction site page. I only need to Re-glue the cone to the basket, and don't need to seal it for any reason. I'm thinking L-pads to keep my...

I have reached out to Roy C here for the cloth surround coating, but i just bought a set of these 2A's and it seems i have all the usual issues with the unmolested speakers. Ill be pulling them to investigate everything. Advice needed on a couple things though please The Speaker cone is...

With speakers like these, Rotating the drivers 180 degrees when reinstalling can help with the woofer Sag.