Hello
I'm looking for a replacement parts for a Pioneer A-6 doesn't seem to be many of them online other wise I would buy one for parts.
The part in question is ASG-408 a bank of 5 switches 12 pins on each switch, they switch the inputs. One of the switches has worn out the plastic latch and...
I recently restored an AU-999 utilizing all the wonderful knowledge members here have on circuit mods and transistor substitutions. It came out outstanding.
That said, the only short coming is the high filter toggle switch is missing the button. I can't really tell, but the shaft itself might be...
OK, so I bought this older kenwood KR-9400 off a guy. Missing the top metal cover, and both wood end plates. I think I can make the wood parts, ok. I would like a top cover that is original, if that is possible. LMK
Hey All, I recently acquired a very clean (No banged up aluminum faceplate) and fully operational SX-D7000. The only thing it needs is a pot cleaning and the replacement of two missing buttons on the tuner. Can anyone recommend a source of 2 plastic rectangular buttons for the tuner section...
Hey everybody, hope you are all doing well. Is there a section of the site dedicated to parts? Caps, resistors, inductors, etc. I have some cap and other part ID questions. Been digging on the web but can't find what I am looking for. Thank you!
Jeremy
I have been repairing 90's Sony minisets for a while. I like them and they're very easy to take apart. All screws. Now I have one that is particularly nice, it's got tape, minidisc and CD. The CMT-CP500MD, or HCD-CP500MD. Minidisc's got MDLP and double speed copy. Anyway, all that tape and MD...
I just discovered that the drive coil cover around the spindle of my SP-15 is cracked.
https://ibb.co/DgsPZLJ
I spotted this available part (SFMGQ20-01) but neither the SP-15 nor the SP-10 are listed, so I’m not sure that it is compatible. The SP-15 service manual does not appear to specify...
Hello,
I am hoping someone might be able to assist me in identifying the Westinghouse player in the photos. It looks a lot like a Westinghouse Rainbow Toner but the face appears to be more up to date and more of a replica of older models.
Also, you will see that it is missing dials and knobs...
Hi folks,
I am a brand new member and have just acquired an SX-1280. The unit works ok but has a couple broken tone control shafts an I am hoping someone can help point me in the right direction to get them replaced. Do any of you have the Bass 50hz ACW-101(ACV-165) and the Treble 10khz...
I am looking for a power button for my CT-17 PreAmplifier. Ive been pushing the little button with the tip of my finger and have some time to get to the little tasks Ive been meaning to do.
Anybody know who would have those? or if somebody has an extra. I actually bought one years ago and cant...
I have a JVC QL-Y55F turntable, I saved it from being tossed in the dump, but it is missing the Tonearm and the dust cover other than that everything seems to function.. My question is two part where can I get the tonearm? I saw a couple on eBay for crazy prices. Are their other models that can...
Where do you find is a good online resource for replacement parts? I have a ‘77 JVC receiver that is missing the correct knob for the on/off switch. I have checked eBay and googled the part by part number, etc. What is my best option for getting replacements for model specific parts?
Pioneer Parts Database
This is a project that I've been working at off and on for the past few years. I started it because of concerns related to the database on the Pioneer Electronics site.
I began by scraping whatever I could get out of the Pioneer Electronics Database. I then added to...
Hi, Folks,
I recently picked up a KA-5700 along with a KT-5300. I shipped the 5700 to a tech for repair, and kept the 5300 on my bench for some cleaning. The interior of the 5300 is immaculate. It looks brand new. The outside needs some cleaning and touch-up, but nothing a little soap and...
Hi Everyone
Vinyl Nirvana has stopped shipping from the USA to the UK because of lack of clarity of the rules post BREXIT. As I continue my rebuild of a TD 160 I wanted to buy a set of the Vinyl Nirvana Springs. Has anyone else encountered this problem and found a cost effective way to...
Hello,
I am new at the forum; forgive me in case of any misunderstanding. I have Akai GX 600-DB, and working on replacing parts of
* Semi-fixed / vol v8k4-1 50kB
* inductor RX 22 mh
* headphone trans. N16 - 535S
I could not find these three components. Could you suggest to me where to find...
Hello,
I have an mx110 but the bottom mounting plate is missing. I have looked on the internet but I can’t seem to find one anywhere. I was hoping someone in the community would have any ideas on where to find one.
thanks,
Blake
Hi all, I recently picked up this table and I'm really enjoying it. It is missing what the manual calls the "arm tube fixing screw" -- you can see in the photo I am pointing to the threaded hole. Does anyone know where to get a replacement or if there is something generic I can use? Seems to...
Hi,
Today I went to a local electronic parts shop where I buy lots of "run of the mill transistor and other brand new "e-waist" :)
The owner had a bit of spare time And he told he might have a nice stack of ORIGINAL **N.O.S** STK Power AMP modules Might be coming up for sale. There are some...
Hi all,
Just wandering... does anyone has experience with Instrumental Parts?
Hunting for some old headphone parts and they claim to have them but now picture is shown ...
Prices seem reasonable...
Any one a good idea about these guy's?
Hi
I got my 5th receiver in .... It is a nice little SONY STR 6046
Goal is to restore it to be functional and keep it in my personal collection.
Upon first check The Amp does run fine, but the reciver part (AM a FM) is not functioning.
Also AUX and Phono only give one channel..
On further...
Hi All,
I've come across a Sony TC-377 tape deck which is cosmetically in superb condition.
I am familiar with these decks and have serviced them before. It looks as if someone was part way through servicing the unit when it was abandoned for whatever reason. All parts are there except for the...
Just got my hands on these today and I'm really excited. I definitely paid more than I wanted but considerably less than they're worth,from what I have researched.
I'm a total rook in the world of vintage gear in mostly all aspects..full disclosure lol
My father's always had 70s era gear so I...
Hi, first time owner and was looking for parts to fix up a Technics SL-3200, specifically the rubber feet and headshell. I was looking through the service manual and for the rubber feet the PN seems to match those of the SL-220, but it the springs in the feet seem to differ between the front and...
Hi Everyone.
I am learning from all of You from some time but this is my first post. I have stumbled upon a problem for which I did not found an answer. I am during restoration of Hitachi HA-5300 and the mentioned speakers relay is in quite bad state (see the attached photos) it don't even have...