• The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html

Old classic Teac A-4010

Vintage TX

Analog forever
Here is an oldie, first Teac A-4010 model made 1968. :thmbsp:
Speed: 3-3/4 and 7-1/2.
Direct-drive reel-motors and belt-driven capstan.
Did spend some major time on this deck.. :cry:
 
Register to hide this ad
When I found this, it was nasty both outside and inside.. :sigh:
But I like challenges building these so a week and a parts-deck later it was ready. :yes:
 
You did a beautiful job Vintage TX! Looks like new "out of the box."
What's the frequency response & S/N ratio for the 4010S?
 
Gorgeous! I have many fond memories of Teac decks from when I was a kid. Very reliable and a wonderful rich sound that seemed lacking in many of the others.
 
Looks like a real cutie you have on your hands there Rolf. I'm still loving my Akai but I could be unfaithful to her for one of those. Like women, the more mature models are the best :naughty:
 
Thanks guys, :)
Frequency response at 7-1/2 is 30 to 20.000 Hz.
- : - 3-3/4 is 30 to 15.000 Hz.
Signal to noise ratio: 50dB
Wow and flutter: 0.12 % at 7-1/2 and 0.15 % at 3-3/4.
One thing I noticed is slow startup time compare to other Teac's, takes 3-4 seconds at 7-1/2 on playmode before speed is stabilized, but 35 years ago maybe that was not so important. :scratch2:
Another is the connections between amp and transport section, replaced the RCA wires with new from Tascam, but I don't like when the wires is on the outside..
 
Last edited:
Vintage TX said:
Thanks guys, :)
Frequency response at 7-1/2 is 30 to 20.000 Hz.
- : - 3-3/4 is 30 to 15.000 Hz.
Signal to noise ratio: 50dB
Wow and flutter: 0.12 % at 7-1/2 and 0.15 % at 3-3/4.
One thing I noticed is slow startup time compare to other Teac's, takes 3-4 seconds at 7-1/2 on playmode before speed is stabilized, but 35 years ago maybe that was not so important. :scratch2:
Another is the connections between amp and transport section, replaced the RCA wires with new from Tascam, but I don't like when the wires is on the outside..
I'm almost sure that was for patching processors into the loop. It wouldn't be my favorite way of doing it either, but it's a remarkable deck nonetheless. One that needs to be preserved and appreciated for a long time :)
 
I have one of those. I don't use it much at all. Just to show people it works. It was a tag sale find and I bought it for nostalgia. I wanted one badly when they were too expensive for me.
 
Hey - That's my deck!

I finally looked up the model number on the TEAC R to R deck I nabbed for FREE from an out-of-business store display (Of course, with permission from the property owner!) And it turns out to be the A-4010S! With the exception of white paint splatters and a paper clip holding one of the reals on the spindle, it looks exactly like the one in this thread.

Other than the fact that the reels actually turn when they're supposed to, I still don't know if it works, but hope to find out soon. I just need to find tape.

I'm a complete noob to late-60's erra gear, so here's a "total noob" question: This thing seems to have a separate preamp on the bottom. Does that deliver line-level output, or is it made to go directly to power amp input? (Doesn't seem likely to be a full blown pre, but I just don't know how alien this stuff is.)
 
:thmbsp:

20658666309_0_ALB.jpg
 
Last edited:
Nice job Rolf!!!!

Reminds me of my 1230. Really ratty and brought back from the dead. Clean up nicely. Finished this years Christmas CD on it. It was rainy here in the Northeast and I ran off and 1 and a half hours of music. Will send you a tape Rolf.

Eric
 
Back
Top Bottom