• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Vintage Sony TA 3650 w/dead left channel

keithpgdrb

Super Member
Hey all,

I did indeed pick up the amp I was talking about in another forum. I found that the left channel is dead through both the Headphone out and speaker out, so its probably something more than a loose wire. I'm not really stellar with DIY, but I really do want to attempt to fix this. It seems like a stupid thing to trash an amp for. Anyone out there with some vintage audio chops got any advice?

Also, does anyone happen to have a service manual for this model? I could buy it, but if the community has it....

look forward to hearing from you all. Here are a few general pics.
 

Attachments

  • P1010001.jpg
    P1010001.jpg
    120.1 KB · Views: 120
  • P1010002.jpg
    P1010002.jpg
    59.2 KB · Views: 122
  • P1010003.jpg
    P1010003.jpg
    152.3 KB · Views: 105
Register to hide this ad
New thread, same forum ;)

Nothing looks bad from what I can see. Do you hear any static when you turn any of the knobs?
 
New thread, same forum ;)

Nothing looks bad from what I can see. Do you hear any static when you turn any of the knobs?

sorry bout the double post on the same unit... I hear nothing from the left channel at all. there is some static on the right when I mess with the volume. maybe that side is on its way out as well, hard to tell, because it cleans up a bit as it plays. I havent really tested it with decent speakers. I only tested to see if it worked on both sides. which it dont. lol. I am going to pick up some canned air to try to clean it out. dont know if it will help because its not really dusty, but its worth a shot.

I just fear I will need to replace something. which will probably be next to impossible. or I'll have to start soldering things. whew..

any advice on a next step?
 
Try working all the knobs (everything, bass, treb, bal, et al) back and forth 20 or more times with the unit off (especially for the volume knob!) and see if that makes any difference.

It's not uncommon for a potentiometer to be so filthy that no signal passes from the preamp stage to the power stage. It just happens with age and environments.
 
I've have one of these: check in the rear the jumpers between the pre-out and the power-in. Exchange the two. You can play a bit to determine if the problem is in the jumpers (the best possibility), in the pre section or in the power section.

All the best

PS: I don't have a service manual, although I wish I had one....
 
ok, I dont know what is going on now. I feel like a bit of an idiot. I messed with all the knobs, and both channels started to function a bit! I changed the jumpers from an rca style to just the metal peg U style, and I even whacked it on the side a bit. Now both channels are Working!! makes no sense to me. There is still some static that seems to be part of the amount of volume. it also seems that the tape 1 section works fine, but both phono areas have the volume/static issue. I'm fairly certain that the turntable is functioning correctly, as I tested it on another amp.

I know for a fact that its been YEARS since this amp has been touched. when I turn it off, then back on again, there is a lot of static until the volume is turned up. Is there cleaning that is needed on something this old? if so, what things should be done, and how? I get the feeling that the unit almost has to be "re" burned in. SO, I have set it up downstairs to just run with my ipod for a while. Maybe that will freshen up the electronics a bit. I'm going to try that and see what happens later this eve.
man, if this works, I'll be so happy. that is, if it actually sounds good when all is said and done. I'm going to use it with a stax hp setup mostly. my own private heaven.

I'm sure I'll need some more advice with this thing, thanks for the suggestions so far.
 
Good likelyhood that you have various coupling or bypass caps failing but before you get to that you should clean and "exercise" all the controls, switches, and connections.

These are nice amps - I recall that they never sold too well but were well behaved and nicely built.
 
My TA-F7B suffered the same fate. After cleaning all the switches and pots, it still wouldn't work properly. Eventually I found the high pass filter switch was so dirty it was cutting out the left channel. Taking it apart and cleaning did the job, works fine now.

Surely doesn't hurt to get some Deoxit and work the switches...
 
Clean the switches is #1 now that you know nothing's blown!

#2; polish the relay contact or replace the relay-- that should fix the problem where you have to turn up the volume then turn it back down-- you're blowing through the oxidation that's built up on the contacts with the higher current and then it's good unit you turn it off, which allows the contacts to reoxidize... if that makes any sense.

Also, letting it run unattended is unadvised... it could very well blow up and you wouldn't be there to stop it in time :tears:. Also, my Sony TA-F6B works VERY well with my Stax setup ;) :thmbsp:

Best of luck with the cleaning!


Philip.
 
I changed the jumpers from an rca style to just the metal peg U style, and I even whacked it on the side a bit. Now both channels are Working!!
Sounds like a bad solder connection..Possibly one of your RCA jacks has a cracked solder connection..
 
ok, I've turned the amp off until it can be attended to. dont want anything to blow up.

I have never cleaned pots or switches and the like. is there a thread with instructions on how to do so? and what do I clean them with?
 
ok, I've turned the amp off until it can be attended to. dont want anything to blow up.

I have never cleaned pots or switches and the like. is there a thread with instructions on how to do so? and what do I clean them with?

You don't have to turn it off and tuck it away; you can listen to it and enjoy it, but I personally wouldn't blast it or leave it on unattended, though. :)

This is a good tutorial for using a product called DeOxit to get the crap outta your controls.
 
I picked up some deoxit, and I was following along with the instructions on how to clean. taking off the top and bottom is a bit nerve racking for me. hopefully it will go well. any advice on the dirty circuit board spots? or should I not worry.
 
Could you take a photo or the board? Personally if it's dirty I wouldn't worry about it, unless it's burnt...

It is best to clean dirt, dust, and grime off as it acts like a blanket and cooks the parts in their own heat, cutting their lives short. :(
 
ok, so I've opened this thing up to clean it. I do not see much that is described in the "how to" thread. I dont see any little holes on the pots. I dont know where to spray on the switches. and the volume pot seems to be encased in a black box! thats the one I really need to get to. I've included a few pics here.

the circuit board pic is to show the dirty I was asking about.

the others are various pics of the switches and such. the black box pic that is buried in wires is the volume pot I believe. I dont see a way in to spray. the knob comes off quite easy. do you think spraying through there will get to the needed places?

any direction would be greatly appreciated. the amp itself seems to work a bit better each time I mess with it, so I think this can be saved. just stuck on the "what next"..
 

Attachments

  • P1010008.jpg
    P1010008.jpg
    100 KB · Views: 70
  • P1010009.jpg
    P1010009.jpg
    103.7 KB · Views: 78
  • P1010011.jpg
    P1010011.jpg
    89.3 KB · Views: 91
  • P1010012.jpg
    P1010012.jpg
    129.2 KB · Views: 89
  • P1010007.jpg
    P1010007.jpg
    67.1 KB · Views: 78
It looks like you'll have to completely disassemble the volume pot to clean it, which involves de-soldering it from the circuit board...

The switches can be cleaned from the front by putting the tube into the space around the switch and spraying it in. The POTs have little gaps here and there that you can use for getting the cleaner inside.

Good luck!
 

Attachments

  • ta-3650-fix.jpg
    ta-3650-fix.jpg
    94.3 KB · Views: 42
  • ta-3650-fix2.jpg
    ta-3650-fix2.jpg
    170.1 KB · Views: 45
well, I did some ripping apart. figured I had nothing to lose. I got cleaner into pretty much everything, and the amp now works, and it sounds great! I have all of you to thank for this. There are still some switches that sound like they need some more cleaning, but now that I have done it once, it will be easy to do.

I was so excited when it started working that I hurried and hooked up my sr-lambda's and my ipod. now, even though the ipod is full of non-lossless files, I have never heard them sound better. this amp is really nice. and it is really powerful as well. I can barely get the volume up to 9:00 without being concerned for my hearing. thats a very new thing for my system.

Next step for me is to get the new cart for my turntable. at that point, I'll have a full vintage set up, and I didnt even mean for it to turn out that way. funny how things work out. after that, I start the search for a new cd player. that will most likely be the most expensive element in the system. that will come much later I believe. but I'll be able to enjoy the vinyl and ipod till then.

again, thanks everyone for helping me figure out what to do. you give me courage to rip things apart!! You guys are amazing. I'm proud to know you.
 
Back
Top Bottom