• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

A little help with my Yamaha PX2, please

Descartridge

Stereos been berry, berry good to me!
My PX2 LT plays well.
Nearly all of the controls work well- Power, speeds, left, right, up, down and cut.
But the most important one is not functioning. When the 30 switch is actuated, the arm is designed to move automatically to the lead in of the disc. Mine does nothing.
I have cleaned the belt area and attempted to deoxit the the 30 switch from the top of the deck without success.
I think that the switch may be oxidized or simply needs to be replaced.
How do I open up the deck to get underneath the problematic switch?
Or is there another cause of this problem?
Thanks a lot as usual.
ehgju8.jpg
 
Register to hide this ad
The bottom plate is removeable, however the trick is turning it over. Firts remover the cartridge, matt and platter. Prepare two padded stands to support the plinth and turn it over front to back, if you turn it side to side, the arm can slide abruptly with possible damage.

Once done the screws holding the bottom plate are obvious. Now if deoxit does not solve the problem the other possibility is a defective optical sensor that tells the arm where to stop and they are near about impossible to find. Should that be the case you can always take the one from one of the other sizes that you do not use.
 
Thanks Merrylander,
Are the optical sensors located on the rail on which the carriage assembly moves?
Or where are they?
Thanks again.
 
They are located on a fixed platform inside the tonearm assembly, the moving part has a shuuter that interrupts whichever one is turned on. If the other two sizes work chances are very good that it is just a dirty switch.
 
Px-2 ym294?

Update:
My tech informs me that I need a proprietay Yamaha IC part# IC YM294. This will correct the auto start and shutoff functions.
Any donor units out there?
Thanks.
 
i have the same problem as you. When i press the 17, 25 or 30 Buttons, the led's light up, but the tonearm doesnt move. if i manually move the tonearm and press play, then press 17,25 or 30, the tonearm lifts back up and moves back to it resting position...

the photo interrupters do light up, but i don't have an oscilloscope to test them...
 
Yamaha used that same IC in the PX-3 as well, if you can find an organ donor PX-3 it could also donate the optical sensors.
 
Hey Merrylander, I've heard you are the PX-2 expert around here :) Ive actually my PX-2 in a repair shop at the moment and they are baffled as top why the Auto buttons wont work. I don't know if they've checked the TACT (?) switches yet but when they are pressed, the LED's do light up.

Unfortunately i don't have a PX-3 to take parts from and both PX-2's and PX-3's are rare in Australia....and luckily mine is a 240V version too. I've had my PX-2 for 2 years now and still cant find someone who will fix it.

I am suspecting that the YM294 may be at fault here. What equipment would i need to find out if it is?
 
I've had a PX-2 for 5 years now and it's never worked in "auto" mode. Since the sensors are unbotanium, my advice would be to just pretend you have a fully manual table (because you do) and use it as such.

I don't see it as "broken" - one you get to that mindset you'll enjoy the PX2 so much more. It would be sad for something else to get broken and render the table totally unusable while they are trying to fix this.

My $.02 - enjoy it while you can, even as a manual table...


jblnut
 
Hey Merrylander, I've heard you are the PX-2 expert around here :) Ive actually my PX-2 in a repair shop at the moment and they are baffled as top why the Auto buttons wont work. I don't know if they've checked the TACT (?) switches yet but when they are pressed, the LED's do light up.

Unfortunately i don't have a PX-3 to take parts from and both PX-2's and PX-3's are rare in Australia....and luckily mine is a 240V version too. I've had my PX-2 for 2 years now and still cant find someone who will fix it.

I am suspecting that the YM294 may be at fault here. What equipment would i need to find out if it is?

Professor Bizzt fixed my PX-2. I suggest you PM him and too bad it is not economical to send it to him.
Mine had the same problems. My YM294 was thought to be bad but was indeed good. My photointerrupters were bad.
Good luck.
 
@jblnut i know what you're saying, but getting the photo interrupters isn't a problems as i know a place that has them.....the YM294 on the other hand...not 100% sure.....yet!

@RDecartridge Ive sent a PM to the Professor....lets hope he replies because ill take any help i can get :)
 
Hey Merrylander, I've heard you are the PX-2 expert around here :) Ive actually my PX-2 in a repair shop at the moment and they are baffled as top why the Auto buttons wont work. I don't know if they've checked the TACT (?) switches yet but when they are pressed, the LED's do light up.

Unfortunately i don't have a PX-3 to take parts from and both PX-2's and PX-3's are rare in Australia....and luckily mine is a 240V version too. I've had my PX-2 for 2 years now and still cant find someone who will fix it.

I am suspecting that the YM294 may be at fault here. What equipment would i need to find out if it is?

I would suspect the optical sensors first, they are a known problem with the PX-2 originals. Generally speaking if you can move the arm with the << or >> switches I will bet on the sensors. Incidentally the PX-2 did not use TACT switches, that was the PX-3. The only IC I have seen to fail (and it really was not a failure, it had been removed) was the PLL chip that controls the motor speed. I was lucky enough to find two in the U.K.

I think someone (Dr. Bzzt?) has found a sub for the opticals.
 
Yamaha PX-2 & PX-3 turntable Sensor C. Board photointerrupters

Hello everyone,

The three photointerrupters on the Sensor C. Board do fail. The LED light emitter part of the photointerrupter is most likely not bad, but the photodarlington receptor part probably is.

Despite much searching, I was never able to find drop-in photointerrupter replacements for the sensor board. Instead I had to dismantle and modify an Omron EE-SX298 slot type photointerrupter. Again, this MUST be modified in several ways...

You diagnose by removing the the tonearm's rear metal cover via two screws under the plinth and verifying that all three photointerrupters are emitting red light. If they are, you know that the transmitter portion of the photointerrupter is functioning.

You then point a strong light such as a desktop halogen lamp onto the rear of the first or between the first & second photointerrupter and press the 30cm auto start button. NOTE: You will have to try different lamp angles and positions until you get this right. If you get a response from the tonearm after pressing the 30cm button, it is very likely that the three photointerrupters are defective.

The two inside and outside leaf lever limit switches should also be cleaned out with a plastic safe contact cleaner without over-spraying and making a mess in the tonearm cavity.

I can repair these sensor boards for anyone with a PX-2 or PX-3 if need be, and am offering this service on eBay as of 12/04/10 at a fair price.


Best wishes, Professor Bizzt
 
Last edited:
You diagnose by removing the the tonearm's rear metal cover via two screws under the plinth and verifying that all 3 photointerrupters are emitting red light. If they are, you then point a strong light (such as a desktop halogen) onto (the receptor side is to the rear) the first or between the first & second photointerrupter and press the 30cm auto start button. If you get a response from the tonearm, it is likely that the 3 photointerrupters are defective.

I followed your advice and indeed i did get a response from the tonearm. When pressing 17, the arm moves for as long as there's light. if i switch off the light before the tonearm cuts off the light to the photo interrupters then it will also drop. So indeed as you and Merrylander suggested the photo interrupters are at fault here.
 
Professor Bizzt fixed my PX-2. I suggest you PM him and too bad it is not economical to send it to him.
Mine had the same problems. My YM294 was thought to be bad but was indeed good. My photointerrupters were bad.
Good luck.

Glad you got it fixed, I haven't had any luck finding the chip.
 
Yamaha PX-2 turntable Sensor C board photointerrupters

Hello everyone,

When diagnosing defective auto start and auto return functions on a PX-2, it is important to not come to the premature conclusion that the unavailable and proprietary Yamaha YM-294 logic control IC is at fault.

Again, do the the light test I recommended in this thread and it is likely you will be in for a pleasant surprise. It is a good feeling to discover that your PX-2 is indeed repairable after doing this test.

You are welcome to private message me for repairing your Sensor C board.


Thanks, Professor Bizzt
 
Nice to see PX-2 help here.

Folks,

I am new to this site, but I am reluctantly selling my PX-2. From poking around the site, the knowledge base here seems quite deep, so I am most likely in the right spot. I take it that it is possible to fix the few issues that it has (45 rpm button and a few others don't work). Does anyone know a site were I could get an idea of the value that is left in this turn-table? If it is worth fixing (and how much that may cost). I have the original box, instructions, all the extras that came with it (even the plastic wrap and styrofoam!). Just not sure how much it is worth in it's current state and where one could post to sell (or fix and sell).

Thanks for your time and passion on these fine vintage instruments!

Greg S.
 
Yamaha PX-2 turntable Sensor C board photointerrupters

Hello Greg,

Don't sell your PX-2! Ask RDecartridge what these sell for. You will be surprised.

It is my opinion that anyone who owns a Yamaha PX-2 or PX-3, a Sony PS-X800 or PS-X555ES, a Pioneer PL-L1000 or PL-L1000A, or Mitsubishi LT-30 or LT-20 or LT-22 would be making a bad decision to sell one of these desirable turntables. There are, of course, other tangential tracking direct drive turntables that are also noteworthy; it's just that the ones mentioned here are relatively common and are popular to collect.

A good tangential tracking direct drive turntable is a wonderful thing; they just require proper treatment and repair sometimes. And this brings me to the topic of care for these tables. However I will have to start a new thread for that as soon as I have time.


Thanks, Professor Bizzt
 
Yep, parts are hard to find which makes precision diagnoses mandatory so that these turntables don't wind up in the landfill.

Too bad there seems to be no way to intercept a turntable's trip to the landfill and start a vintage turntable parts warehouse so that we could all have access to parts when need be. Hmmm... Any thoughts?

Regarding headshells; I have found that the Stanton H4-S universal bayonet style headshell is probably unbeatable for the money when lightly damped on the underside with GC Electronics high voltage putty and the finger lift clipped off.


Best wishes, Professor Bizzt
 
Back
Top Bottom