• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Another Super High End Phono Stage! No expense spared...

sesame wood enclosure for CNC

HI ,
Today I have bought sesame wood jewelry box for CNC phono stage.Some pics:
 

Attachments

  • DSC04574.jpg
    DSC04574.jpg
    51.7 KB · Views: 266
  • DSC04577.jpg
    DSC04577.jpg
    67.1 KB · Views: 190
  • DSC04576.jpg
    DSC04576.jpg
    56.8 KB · Views: 218
10pF empty slot?

I don't feel like reading thru this thread again so I'm just checking to be sure the 10pF slot is there for additional capacitance should I need and I can leave it empty... correct?

Now to fit it to my box and give it a whirl.

Cheers,

Bob
 
I don't feel like reading thru this thread again so I'm just checking to be sure the 10pF slot is there for additional capacitance should I need and I can leave it empty... correct?

Now to fit it to my box and give it a whirl.

Cheers,

Bob

You are correct. Whirl away!
 
Hooked it up and it works!

Alrighty now... I built it and it works. My dog woke me up so instead if thinking about it the rest of the night I got up plugged it in. It does sound pretty good. I initially had a hum but I plugged in my ground from my TT to the turntable ground on my preamp and the hum is gone. I tried a case screw and it didn't totally remove the hum. I don't hear much clics on the LP I'm listening to now and I'm wondering if the highs are rolled off a little. Doesn't sound like it from the music but no clics (very little) on an old record...kinda unusual in a good way. Gonna have to take a listen to more LPs as see.

Took me about 4 hrs to have the box in hand with a LED light lit and ready to play. I got tired of soldering and while hooking up the batteries and wire for them I forgot to put the wires thru the hole to the switch (2x) duh. I always say 3x a charm. Then I forgot to put the collar on that holds the switch in place...and of course soldered everything back together. It's gonna have to do. If the switch gets loose I've got some glue that works!

So I'm sure this TT pre is quieter than the TT preamp (Citiation 17 total rebiuld my me) I was using. Gain is a little less.

So all in all I'm satisfied. I'll post pics of my build later today. I just wanted to see if it worked, so I'm good.

I'll have to do some more critical listening and try a swap back and compare.

Thanks to the Toadster and everyone else who helped to make this happen.

Oh and I have a few other ICs to roll in too and will report back on that. I've got some TL072 and AD823 IC's waiting to go into another build (ESP P06) I haven't started yet.

Now all I need is a line level board to build and my TT rig will be totally home made.

Cheers,

Bob
 
Last edited:
Bump... I guess everyone is busy with the solder iron!

Listening now... I'm going to have to hook up a 2nd TT to my preamp TT input and do some critical listening.... but first ahhh a sip of wine. Me thinks the bass is actually rolled off. I've got speaks that get down LOW and I'm missing some of it. Gonna have to get out some Meters LPs and see whats what. Vocals are tremendous as is the ol guitar and harmonica, which I gotta say I love.

My ol preamp is singin to me now, something like this:

Tell me that you love me
can't stand to see you go...

baaaayyy-bee tell me that you love me
I can't staaaand to see you go.

Yeah U right!

Ooooh yeah there's the bass... just had to turn it up!

Only thing missing is my budz...

Cheers,
Bob
 
Good deal, Bob! What did you start with for op-amps? We found quite a range of frequency response depending on what pair we put in the sockets.
 
Good deal, Bob! What did you start with for op-amps? We found quite a range of frequency response depending on what pair we put in the sockets.

I just used what was in the BOM, looks like the AD823. Which op-amp has the flattest freq. curve of the ones you tried?

The TT I'm currently using has standard TT cables supplied with the TT Pl-707 and a MA 3002-II cart which is very good. BTW I find this preamp to be very quiet. I've need to turn up my volume to say 3 o'clock to hear it, which would be defening if music was playing.

Cheers,

Bob
 
Oh yeah, mine arrived yesterday. Won't have time to do anything until at least next week though.

Thanks, Phillip.
 
Hi,

With the great support of Phillip,Felix and many AK members I have soldered my CNC PCB.This is my first DIY project.This is first time I have soldered anything.I have a confusion for power connection.I am not able to understand wire connection between toggle switch,batteries and PCB.Could anyone help me out.A closeup pic would be helpful.I am attaching some pics including toggle switch, suggestion welcome.



Regards,

Sachin
 

Attachments

  • DSC04585.jpg
    DSC04585.jpg
    88.5 KB · Views: 384
  • DSC04586.jpg
    DSC04586.jpg
    83.4 KB · Views: 323
  • DSC04587.jpg
    DSC04587.jpg
    60.3 KB · Views: 312
Hi,

With the great support of Phillip,Felix and many AK members I have soldered my CNC PCB.This is my first DIY project.This is first time I have soldered anything.I have a confusion for power connection.I am not able to understand wire connection between toggle switch,batteries and PCB.Could anyone help me out.A closeup pic would be helpful.I am attaching some pics including toggle switch, suggestion welcome.



Regards,

Sachin

Your board has 3 power connections marked G - +. You will have 2 batteries, each with a minus and plus. What you will be doing is connecting the two batteries in series, that is, connect the minus of one to the positive of the other. This connection will also be wired to the G connection on the board.

Now the remaining + terminal of the batteries, the one that doesn't have a connection on it yet gets wired to one of the upper terminals on the switch. The terminal of the switch directly below that one gets connected to the + terminal of the board.

Finally, the remaining - terminal of the batteries, the only one left that doesn't have a connection, gets wired to the second of the two upper terminals of the switch. The lower terminal of the same side of the switch, now the only one left that does not have a wire on it, gets wired to the - terminal of the board.

Hope this helps.

Shelly_D
 
Your board has 3 power connections marked G - +. You will have 2 batteries, each with a minus and plus. What you will be doing is connecting the two batteries in series, that is, connect the minus of one to the positive of the other. This connection will also be wired to the G connection on the board.

Now the remaining + terminal of the batteries, the one that doesn't have a connection on it yet gets wired to one of the upper terminals on the switch. The terminal of the switch directly below that one gets connected to the + terminal of the board.

Finally, the remaining - terminal of the batteries, the only one left that doesn't have a connection, gets wired to the second of the two upper terminals of the switch. The lower terminal of the same side of the switch, now the only one left that does not have a wire on it, gets wired to the - terminal of the board.

Hope this helps.

Shelly_D

Thanks Shelly for explaining,but I am still very much confused a pic might help.

Regards,

Sachin
 
This might help as well

attachment.php
 

Attachments

  • CNC-Switch.JPG
    CNC-Switch.JPG
    90.1 KB · Views: 586
Back
Top Bottom