• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

ADS 710 - Restoration

The resistors don't need to be replaced unless they are bad as they don't age like electrolytic caps do.

There is only one electrolytic cap that needs to be changed. The yellow boxes are film caps and those don't age. I pulled some from ADS speakers, one pair and measured them. The 4.7 measured 4.8 and 5.1, the 10s measured 10.5 and 10.8 all are within the 10% range. Maybe it would be better to see if my L710s could be more closely matched for these caps, but I have not measured the ones in the speakers. And @BigElCat mentioned that changing them didn't make the speaker better as different film caps have different sound in the mid and tweet outputs.


It is really hard to go an expensive route replacing the electrolytic with a new electrolytic. The 100µF/100V electrolytic cap is generally under a couple few bucks. But partsconnexion does have some Audio Note Kaisei caps in that value that are kinda spendy as well as some others starting at 90¢ each. Just putting in a new electrolytic will get the speaker back to like new. parts express will also have a 100/100
 
The resistors don't need to be replaced unless they are bad as they don't age like electrolytic caps do.

There is only one electrolytic cap that needs to be changed. The yellow boxes are film caps and those don't age. I pulled some from ADS speakers, one pair and measured them. The 4.7 measured 4.8 and 5.1, the 10s measured 10.5 and 10.8 all are within the 10% range. Maybe it would be better to see if my L710s could be more closely matched for these caps, but I have not measured the ones in the speakers. And @BigElCat mentioned that changing them didn't make the speaker better as different film caps have different sound in the mid and tweet outputs.


It is really hard to go an expensive route replacing the electrolytic with a new electrolytic. The 100µF/100V electrolytic cap is generally under a couple few bucks. But partsconnexion does have some Audio Note Kaisei caps in that value that are kinda spendy as well as some others starting at 90¢ each. Just putting in a new electrolytic will get the speaker back to like new. parts express will also have a 100/100
Thanks a lot. Seems like a no Brainer to change the one cap. I'll give it a go with the standard replacement.
 
Just opened mine up. It's a 90 mfd 100 vnp cap. Guess it's a little different than the 100 100. Anyone have any suggestions for a replacement?
 
Last edited:
I opened my 710 today. I had no sound from tweeter so was hoping to find a loose wire. Luckily I found one (wire connecting to the fuse) was loose.

I did find some debris or flaking coming off one of the resistors (I think it's a resistor). It came off the little 1.5 ohm box. (shown in picture).

What is this stuff and what does the 1.5 do?
 

Attachments

  • PXL_20221009_131508424.MP.jpg
    PXL_20221009_131508424.MP.jpg
    67.9 KB · Views: 34
  • PXL_20221009_131539059.MP.jpg
    PXL_20221009_131539059.MP.jpg
    75.1 KB · Views: 35
Last edited:
That is just a cement resistor and some of the cement is coming off don't expect it to be an issue.
 
Just opened mine up. It's a 90 mfd 100 vnp cap. Guess it's a little different than the 100 100. Anyone have any suggestions for a replacement?
Sorry for the bump. But does anyone know if there would be any issue using the 100 100 cap in this instance?
 
With a 90µF cap installed, made with a ±20% tolerance, a 100 cap is just 11% high so it shouldn't sound much different to a computer analyzing the sound. So probably the same to you as far as the cap value change is concerned.

you could put two caps in parallel to add up to 90 if you are so inclined.
 
Back
Top Bottom