• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Altec amplifier ; What do I have here ?

mfaz28

Active Member
IMG_0908.JPG IMG_0912.JPG IMG_0910.JPG IMG_0909.JPG IMG_0925.jpg At first I though it was a home brew, mono power amp (2 6L6's) and separate power supply. But I did find a very similar factory built A-333A (although one chassis) from an old Altec add. And upon close inspection, it does look like a factory piece. Can anyone assist in identifying what it is?
 
Register to hide this ad
Its got a very distinct Williamson amp look to it. The early ones were often two piece, with an umbilical cable going between the power amp and the power supply. I'll go with homebrew or a kit here, screws for tube sockets is usually a big clue. Factory stuff is almost always riveted. If its got Altec iron, its probably a very nice amplifier.

The only thing that doesn't look like the usual Williamson lineup is the second tube on the power supply. Looks like a gas regulator, maybe for the screen supply? Otherwise looks like a pair of 6L6GC, two 6SN7 and a 5V4 rectifier, which is the usual setup for one.
 
Gadget, Thanks.....But several images of the Altec A-333a on the net all show screw down sockets. Perhaps early Altecs from the late 40's early 50's used screws and then later rivets? IMG_0911.JPG IMG_0913.JPG
 
Perhaps early Altecs from the late 40's early 50's used screws and then later rivets?
Not impossible. Large production tends to use rivets just because they are faster to install than screws and nuts are. Maybe in the early days they weren't building enough to justify the cost of a rivet gun.
 
I think it has a posibility to be a home brew, or a professionally put together one-off amp built for a studio or something.

I'm not an expert at all, but I have drooled over Altec stuff my entire tube hungry life, and although it looks extremely well designed, it just doesn't scream Altec to me. I doubt Altec would have had to borrow a choke from Chicago to get a production done... Even if they did source a choke, they would have potted it :)

One thing is for sure, those giant transformers are Altec!

Let's see some of the wiring!

Beautiful amp man, congratulations that's some serious iron.

I think you are on the right track with the time period, with the 333, I also saw a 323, but its not quite the same either... but its close. what's the number on the other transformer?
 
Last edited:
Definitely not an ALTEC but a very well built homebrew amp using ALTEC transformers. I can't find anything remotely similar to it in my old ALTEC (Hi-Fi and Pro/Studio) documents collection.
 
The power supply transformer is the TQM-601. The amplifier section transformer is the TQM-201 A. Any info on these? Additional wiring pictures as requested. IMG_0933.JPG IMG_0935.JPG
 
Just lucky to have stumbled across it many years ago. I even forgot it was in the basement. Looks like it's worthy of a restoration effort, even just for a sweet mono set-up. I'll never find a matching set for stereo. Perhaps an open baffle that I've been wanting to build with a 604b? Any replacement parts suggestions?
 
That is an odd duck. I'd guess early 1950s but no earlier. It still has the oiginal Altec decal but uses the later style Peerless "Q" case. It's not homebuilt but it's not official Altec either. It may have been built by Altec for a 3rd party by or by another manufacturer using a special run of Altec transformers. The numbers sort of fall within Altec's original naming convention but aren't identical. I've never seen them catalogued before and have decent info back to 1947 on their transformer offerings.

/a mystery but a cool one
 
With the handles on them, they remind me of portable mono PA system amp, I bet it does sound good. Pretty cool acquisition there Brother!!! Probably very comparable to a MC60
 
Thanks ! Looking for ANY additional help with this. Since I'm going to overhaul it. I'm wondering if these transformers are worthy of better tubes?
 
Soundmotor, thanks.... Maybe industrial part numbers on those transformers? I wonder, if that's true, that they would qualify for hifi use? Hopefully not just to yell over the PA; "Brake time is over, Back to work !!" .....
 
Soundmotor, thanks.... Maybe industrial part numbers on those transformers? I wonder, if that's true, that they would qualify for hifi use? Hopefully not just to yell over the PA; "Brake time is over, Back to work !!" .....

Although I suspect they are good, without sweeping the the output transformer you really won't know.

However, Altec was at the high end of the fidelity food chain when your amp was built and I'd bet that it performs well.
 
There are some things sold as "PA" gear that well and truly do not suck. The physical size of that transformer makes me suspect that one probably does not. Honestly I don't suspect its PA at all. I don't see a bunch of un-used taps, and PA trafos almost always had them. 70v or 600 ohm output was common, along with a number of other options most of the time. Hifi trafos usually were 4,8,16 ohm at most and 4 ohm wasn't always an option.
 
Gadget, Thanks again. I'm still digging around to try and chart the best resto-course. Wondering about SE or triode connection?
 
Back
Top Bottom