• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Fixable gear

Bstable

Super Member
Well the vintage bug has infected me. One problem though. As I search for vintage gear I can usually find pictures and specifications. What I don't know is if parts are still available should something go wrong. I would like to know your opinions and experiences on what gear is still very fixable, and what gear should be avoided. I am not talking about high end equipment, more like quality Japanese gear of the 1970s. I am not trying to stir up a hornets nest here so NO FIGHTING. I look for gear with good specifications as well as looks, but good looks does not mean it will be repairable. I know this might seem vague, but I learned my lesson with a Yamaha CR-640 receiver I bought. Never abused it and it still looks great, but am told it is probably can't be fixed because of an unobtainable power pack:sigh:
 
Last edited:
Register to hide this ad
I know this might seem vague, but I learned my lesson with a Yamaha CR-640 receiver I bought. Never abused it and it still looks great, but am told it is probably can't be fixed because of an unobtainable power pack:sigh:

In the case of something like this you could always look for a parts unit that has something different wrong with it. Kinda like working on cars, computers, etc...
 
The problem is that most equipment from that era will have some parts that can not be bought except by getting a parts unit. The only companies I know that universally support their line that far back are McIntosh and Audio Research. There are a number of excellent techs who can backwards engineer and then fabricate replacements either through circuit mods that will support new components or can fabricate replacements such as the STKs. It is usually easier to actually go back further in time to tube units as they tended to use more stock items. Most of the time the hardest part to find a replacement for are the electrolytic cans.

As for the run of the mill stuff from Pioneer, etc. it probably is easier to find replacments for the low to middle of the line where more parts are likely to be off the shelf and yes stay away from units using STKs if possible. Nice idea but almost unobtainable now.
 
The problem is that most equipment from that era will have some parts that can not be bought except by getting a parts unit. The only companies I know that universally support their line that far back are McIntosh and Audio Research. There are a number of excellent techs who can backwards engineer and then fabricate replacements either through circuit mods that will support new components or can fabricate replacements such as the STKs. It is usually easier to actually go back further in time to tube units as they tended to use more stock items. Most of the time the hardest part to find a replacement for are the electrolytic cans.

As for the run of the mill stuff from Pioneer, etc. it probably is easier to find replacments for the low to middle of the line where more parts are likely to be off the shelf and yes stay away from units using STKs if possible. Nice idea but almost unobtainable now.

Thank you Brian. That is the kind of info I was looking for. I guess my CR-640 had STKs. If I were to find another 640 (working) Do you think I would run into the same problem all over?

Bryan
 
Simple answer is to switch to vintage tube. ;) Paradoxically, parts are virtually no problem for most of these because anything that is unobtanium can be replaced by something similar with just a little adjustment.

mike
 
Japanese amp's from the 70's stay off anything that sayes V-FET, you need another unit for spear parts.

Also Yamaha CR-xx40 (as you by now know), but there is a work around this problem. Do a search for STK in the vintage forum.

But in general, invistigate any unit before buying or consider the door stopper possibility in the price when you buy.
 
I'd suggest firing off an e-mail to Merrylander as to the possibility of getting the Yamaha up and running again. He is a Yamaha guru and can give you the real dope on it. There is nothing like having a specialist as to a marque and we are indeed very fortunate to have Merrylander for Yamaha.
 
But sometimes vintage is about LOVE. A guy is in love with a particular model. He buys 3 units..... back ups!
 
Brian with all respect, there is over 46.000 members here on AK; if all send e-mails to merrylander asking about gear they are thinking to buy, he worn't have mutch time to do anything than writing e-mails back!

I suggest to post in the forum, just like now. marrylander or any other with Yamaha repair experince (and there are more) wil answer if they have time.
 
If you reread the original post, last couple of sentences you'll see he has a Yamaha CR-640 in very good condition that is in need of repair and has apparently been told it is a doorstop. Merrylander has a lot of experience with Yamaha and rather than junking it, Merrylander may have a solution. Yes, he is a busy person and may not be following the thread. I know I can not follow every thread started on this site.
 
Going back to the original question, I would say that MOST vintage gear can still be repaired. MOST of the time, parts are still available, if you can order online.

For SOME gear, some parts are unobtanium. Sometimes there are work-arounds for these, and sometimes there is no alternative but to find a donor unit ...which may have the same issues.

I'd suggest "when in doubt, check it out", by coming and searching or asking here on AK about the particular model. The "unfixables" are around, but they are more the exceptions to the rule; MOST vintage gear is repairable, in my experience.
 
Well said "the real mandak"

Merrylander has been so overwhelmed by work that he stopped taking new work, please give the man a break......

He does come around and answers questions at his own pace when he can. Answering personal emails takes a lot of time, it is better when he answers questions from postings, that way everyone can benefit from his wisdom.....

Remember he does it for fun: Do not take the fun out of it.
 
Yamaha CR-640

But sometimes vintage is about LOVE. A guy is in love with a particular model. He buys 3 units..... back ups!

I have tried to buy back ups on e b** , but it always get to the point in price where I have to say "with shipping I am going to spend $80 on something only to spend more on the "fix" that may or may not even be possible with the spare unit". Yes I am on the hunt for a CR-640 locally. I tried to get it fixed (locally) 18 years ago and that was a nightmare. Not sure what to do at this point with my cosmetically perfect "doorstop"
 
Bstable,

The main unobtanium component is the predriver module. Someone else has determined that an alternative module can be used to replace this component. See post 62.
http://www.audiokarma.org/forums/showthread.php?t=86220&highlight=yamaha+predriver&page=2

Merrylander has also done a reverse engineering of the part in question, but I don't think anyone has built and successfully tested it. I made 2 and neither worked quite right most likely due to errors of construction or parts choices.
http://www.audiokarma.org/forums/showthread.php?t=59358&highlight=cr-840
http://www.audiokarma.org/forums/showthread.php?t=145244&highlight=Yamaha+CR-n40s

I also think that the entire output section could be replaced with a chipamp like the gainclones. You might not consider a Yamaha anymore, but many find the gainclones to sound good. It would at least keep the unit functional and I don't think that's such a bad deal.

Good luck,
John
 
While finding an exact backup would be great, I settle for similar units. Around here Sansui's 9090s and one 9090db have shown up at garage and estate sales and thrifts at cheap prices. Also a Pioneer SX-1010. The db model is known to often have problems so I was glad to get a 9090 to back it up. I am not talking a parts doner but back up. I look until a bargain comes along, do not epay prices and no other bidders.

It pays to be flexible and take the popular makes and models that will be easier to find in your location. Around here I have never seen a Yamaha or Concept for example.

Charlie
 
Yes buying components that are common is another way to go. Easier to find parts if there were a lot made. Interchangeability is a plus.
 
I am at a stage in life that I know what pleases my ear: vintage Sony (also Mac MC240 and EL84 amps). Vintage Sony is relatively cheap, but is not serviced by Sony; so I am always on the look out for bargains units of the models that interest me.
 
Back
Top Bottom