• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Help finding a relay source for Crown preamp

jbpollock

Well-Known Member
I have a Crown IC-150 preamp that has a defective reed relay. Preamp works great with relay bypassed, but I am having a hard time finding a source for a replacement.

Relay is labelled: Midtex/Aemco 172-161SA1 or 172-161SAI. Not sure about the last character. Also on the relay is the number 7401.

Info from the service manual says: Relay: 5k ohm, DPDT, NC, reed

Any help is appreciated!
 
Register to hide this ad
What coil voltage is it 5v,12v,24v according to the schematic?
 
Will get a photo as soon as I can get the cover back off. I can't find the voltage on the schematic. Its not on the diagram or on the parts list....I will look elsewhere
 
Attached are pictures.

P1010143.jpg


P1010142.jpg


P1010144.jpg
 
The Crown Part number listed in the service manual is 3496. Crown still lists a part C-3496-4 which is listed as being a 5 Kohm DPST NC Reed Relay for $30.19. Sounds like the right part except that it is listed as DPST and the service manual says DPDT? Don't really know what this means though. Apparently not all parts on the list are actually available, so who knows.
 
DPDT double pole double throw
DPST double pole single throw
service manual says DPDT?
typo ?? The actual relay doesn't have enough pins to be a DPDT. The schematic shows a DPDT but 2 pins are not used. Its probably the right relay..
Looking at the schematic it looks like a 24 volt
Crown is pretty proud of that part...$30 yikes
 
On the 150, you must short the appropriate rear jacks for the relay to work.
Have you done that?

DH

I have a Crown IC-150 preamp that has a defective reed relay. Preamp works great with relay bypassed, but I am having a hard time finding a source for a replacement.

Relay is labelled: Midtex/Aemco 172-161SA1 or 172-161SAI. Not sure about the last character. Also on the relay is the number 7401.

Info from the service manual says: Relay: 5k ohm, DPDT, NC, reed

Any help is appreciated!
 
On the 150, you must short the appropriate rear jacks for the relay to work.
Have you done that?

DH

Nope...had no idea.....unless you are referring to the two posts that have to be connected that are designed for an external muting switch, then yes...
 
Crown forums:http://www.crownaudio.com/forums/
Nice place with some of the factory guys quite active and good with troubleshooting even the old stuff.

There's also a Crown repair facility for their legacy stuff:

AE Techron contact information / http://aetechron.com/contactus.htm
Mailing address: AE Techron Phone: 574-295-9495
2507 Warren Street Fax: 574-295-9496
Elkhart, IN 46516 E-mail: service@aetechron.com

Brenda Price has always been extremely helpful in the Crown parts department: http://www.crownaudio.com/gen_htm/concrown.htm
 
Thanks for the links. I was looking at the service manual again, and although I did not find any info regarding shorting pins, aside from where not to put them, I think I need to trouble shoot a little more. Turns out that although the relay is the problem and bypassing it does fix the problem, there is a whole circuit dedicated to providing power to trip the relay, causing it to switch to the on position. So, the relay could be the problem, or it could be some other component in the relay circuit. Sort of wondering if it would be better to bypass the preamp relay altogether, since it is not protecting the speakers in the same way as a power amp relay.
 
Back
Top Bottom