• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Marantz 1070 Recap List

peter_ng

New Member
Hallo to All Senior:wave:
I'm going to Recap Marantz 1070, as below i list down all the Electroly Cap need to replace according the service manual...
The replacement capacitor is searching on Digikey..some i haven list down yet is i haven found option from Digikey,
hope all Senior can help me complete the list & verify for me,before i go order...
If the list wrong or have better recommendation please help me update the list.:ntwrthy:

P800 Power Supply Board
C803 220uF 63V - Nichicon FG 220uF 63V
C804 100uF 50V - ELNA SILMIC II 100uF 50V
C805 10uF 35V - ELNA SILMIC II 10uF 35V
C806 100uF 50V - ELNA SILMIC II 100uF 50V

P400 Phono Board
C401 1uF 50V - ELNA SILMIC II 1uF 50V
C402 1uF 50V - ELNA SILMIC II 1uF 50V
C405 22uF 6V - ???
C406 22uF 6V - ???
C409 47uF 16V - ELNA SILMIC II 47uF 16V
C410 47uF 16V - ELNA SILMIC II 47uF 16V
C425 100uF 50V - ELNA SILMIC II 100uF 50V

PE01 Pre Tone Board
CE03 10uF 35V - ELNA SILMIC II 10uF 35V
CE04 10uF 35V - ELNA SILMIC II 10uF 35V
CE05 4.7uF 35V - ELNA SILMIC II 4.7uF 35V
CE06 4.7uF 35V - ELNA SILMIC II 4.7uF 35V
CE07 1uF 50V - ELNA SILMIC II 1uF 50V
CE08 1uF 50V - ELNA SILMIC II 1uF 50V
CE09 1uF 50V - Nichicon Muse ES BP 1uF 50V
CE10 1uF 50V - Nichicon Muse ES BP 1uF 50V
CE11 3.3uF 50V - Nichicon FG 3.3uF 50V
CE12 3.3uF 50V - Nichicon FG 3.3uF 50V
CE13 100uF 35V - ELNA SILMIC II 100uF 35V

C001 10000uF 50V - Nichicon KG 10000uF 50V
C002 10000uF 50V - Nichocon KG 10000uF 50V

P700 Power Amp Board
C701 3.3uF 25V - ???
C702 3.3uF 25V - ???
C705 47uF 16V - ELNA SILMIC II 47uF 16V
C706 47uF 16V - ELNA SILMIC II 47uF 16V
C709 47uF 50V - ELNA SILMIC II 47uF 50V
C710 47uF 50V - ELNA SILMIC II 47uF 50V
C719 220uF 50V - ELNA SILMIC II 220uF 50V
C720 10uF 35V - ELNA SILMIC II 10uF 35V
C721 47uF 16V - ELNA SILMIC II 47uF 16V
C722 220uF 10V - ELNA SILMIC II 220uF 10V



Thank You!
 
Register to hide this ad
Hello !
Do I qualify as Senior at 42 ? :D or was it not age you were referring to ?

The Marantz manuals a known to have plenty of errors...
And the writings on the boards themselves also have errors...


The best way to do a recap (even experienced technicians work like this) :

1) open your amp and note down on paper, each board separately, what electrolytic caps you see (capacity / rated voltage)

2) order your new caps from your list - do not take any caps out of the amp yet !

3) when you have the new parts :
- note polarity of the cap you are going to take out
- take old cap out, look again at the capacity/voltage, make sure the new one you are going to put in is the good one
- solder in the new cap making sure you respected the polarity.


When you finish a board, test the amp with a Dim Bulb Test in line. If something went wrong at least you know which board to look at...

Beware, there are some electrolytic non-polarised capacitors sometimes.
This method might take a bit longer, but is much safer.

I've been using Elna Silmic II (RFS series) with great results. And Mundorf for the main power supply caps. More expensive but your time is worth the little extra expense IMO.
 
Last edited:
Back
Top Bottom