• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

MCS 683 8227 score!

lowercasee

Active Member
Scored some really good condition MCS 683-8227s yesterday for $30. Unfortunately, the oem woofers are long gone but the replacements (Radio Shack 40-1034s) seem to be a good fit. Cabinets are in great shape, as are the tweeters and mids. Would love to get oem woofers but I kinda doubt that will ever happen. Nonetheless, quite happy with them. Very nice sound and I really dig the looks. I have one half of the United Speaker made MCS now too! Hope to get the 8226s and 8228s someday.

20201005_191512.jpg 20201005_191443.jpg
 
Register to hide this ad
Luckily they're sealed cabinets, which makes the odds of a third party woofer working much better.

Do you happen to know the ohm spec of the stock woofer? The ones in it now sound fine and are in range for the cross over frequency but I am curious about the stock ohm rating.
 
Do you happen to know the ohm spec of the stock woofer? The ones in it now sound fine and are in range for the cross over frequency but I am curious about the stock ohm rating.
It is a 4 ohm woofer. I believe the Radio Shack one is a 8 ohm woofer..The MCS woofer has a 2" voice coil. I believe the RS is a 1.5 " voice coil.
 
Last edited:
It is a 4 ohm woofer. I believe the Radio Shack one is a 8 ohm woofer..The MCS woofer has a 2" voice coil. I believe the RS is a 1.5 " voice coil.

Thanks for the heads up and the pic. The RS woofer seems to work pretty well in it so far. I have my Onkyo Integra TX-890 playing some Carpenter Brut through them right now at moderate sound levels and there's no shortage of low end, ha! That said, I would prefer to get 4 ohm speakers in there if I can to get closer to oem. Any suggestions?

Looking on Parts-Express and the one below looks like it may not be a bad choice. I think the x-over on the woofer is 2000Hz and that falls into that range.

https://www.parts-express.com/goldwood-gw-212-4-12-oem-woofer-4-ohm--290-330

Saw this one too but it's effective range is only up to 1500Hz so not sure it would be as effective.

https://www.parts-express.com/goldwood-gw-1244-12-butyl-surround-woofer-4-ohm--290-366

Edit: looking at the specs on Goldwood's site, it says the 1244 frequency response is 18 - 4,5000Hz. It has a 2" VC too so it might be the best bet to get closest to OEM.
 
Last edited:
That looks to be a good quality woofer. I hope the screw holes line up well for you. If you decide to replace the capacitors, I can tell you there are 4 caps in each X-over. Two will be a pill type 1uf and 2uf. The others will be a 10uf and a 50uf or 75uf. One pair of crossovers in mine uses a 75uf and my spare uses 50uf.
 
Thanks, I appreciate help! The caps all looked to be OK in mine so I think I will leave them as is for now. Will see how the speaker replacement works and then go from there.
 
I think I am going to go with the Goldwood GW-1244. Seems like it will be a good fit for the 8227.
Before you make the purchase, you may want to model that woofer using the cabinet's internal dimensions. You can use free software like WinISD to do it. Also check the woofer's impedance graph (should be on the spec sheet) and see if the crossover needs to be modified to maintain the same crossover frequency as the original.
 
Before you make the purchase, you may want to model that woofer using the cabinet's internal dimensions. You can use free software like WinISD to do it. Also check the woofer's impedance graph (should be on the spec sheet) and see if the crossover needs to be modified to maintain the same crossover frequency as the original.

Thanks for the tips, will look into it.
 
Back
Top Bottom