• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Scott 210-D Integrated- Output Transformer

el-37

Active Member
Hello,

Anyone have any knowledge on the Scott Mono stuff??? There seems to be very little information out there. I have a 210-D here on the bench, and the output transformer went up in smoke. I think it probably got wet sometime in its life.

My question is- does the 210-D share its output transformer with any other Scott unit??? I am going to call Heyboer tomorrow and see if they can make one for me, but if someone knows of a good used one, please let me know.

Plus...anyone running a Scott 210 series amp??? I am curious about peoples impressions about the amps.
 
Register to hide this ad
Wish I could help you on that one. The 210 series is not common at all. Heybour is going to have to reverse engineer a transformer for it. No data available that I know of so they would have to tear your old one down to make a new one or just fudge you one that will work. Expensive to do for one piece.

Craig
 
Craig,

I figured Heyboer would probably not have the specs- or if they do Phil would not be able to find them!!! Phil is a great guy, but he admits that their files could be better organized.

I am beating the bushes to see if someone has a used one and/or parts unit lying around. From what I gathered the 210-C uses the same iron as the 210-D. Hopefully I am successful.

The SAMS folder seems to have some mistakes. It lists the primary impedence at 1.42K- which seems quite a bit low for a pair of 6L6's. I think it is supposed to be 4.2K.

I can't shake the feeling that this amplifier is going to sit around for years until a transformer pops up somewhere!!!
 
NOSValves said:
Heyboer is going to have to reverse engineer a transformer for it. No data available that I know of so they would have to tear your old one down to make a new one or just fudge you one that will work. Expensive to do for one piece.

Craig

Hey!!!,
While it may turn out to be expensive for one piece, the folks at Heyboer are *VERY* skilled at unwinding. They are the ones I sourced the machine wound and modified S265's from.

They're doing an even bigger one for me right now, the 80W, 5k a-a, S-271-S from the 20-20 Plus line. That job isn't done yet, so I'd only be able to guess what copies are going to cost. If I apply a size scale factor, maybe $150 each for the big one, or nearly twice what the 265 goes for...:)

Heyboer has winding data on a lot of things, I've never asked for one of these. They may already have this one on the books. You may want to upgrade both amps with new OPTx's, as it may be better( as in less expensive ) in the long run. I'd bet that Heyboer has more than one design that could be considered a step up from the original.

What are the specs( a-a load, wattage...) on that output? Do let us know if you find any other options.
cheers,
Douglas
 
The Sams folder says even less than usual... 4.2K CT to 16/8/4/2 Ohms, with screen taps (which aren't connected). No power rating, no DC resistance, not even an HH Scott part number. It's a through-chassis mounting, so even replacing it with a Hammond will require swapping end bells.
 
Tom,

Thanks for chiming in...I am actually working off the SAMS scan you sent me the other day. On the scan I could swear it says 1.42K ohms CT.

It is a unique transformer, it only has one bell on the backside (side facing the rear of the chassis) and instead of wires it has terminal posts.

I am hoping a Hammond 1650-N will work. It has a 4300ohm primary. Mounting it will be interesting.
 
Does anyone have access to a Scott 99-B, 99-C or 99-D SAMS Photofact???

If so I am interested to know if the output transformer primary impedence is the same or close. If someone could post this info it would be a great help.

I have a lead on some 99 outputs, and if they will work that would be a lifesaver!!!
 
I have the Sam's for a 99D and it lists the output as being 7.3K CT part # TRA-10-14-1 with TRA-10-14 being a suitable replacement. Is the transfomer on your amp a lay down configuration like the 99 series? I honestly have never seen a 210 series amp.

Craig
 
I have a scott 210-E that I've been trying to track down a mate to for a stereo setup.
It has a simular output trannie as you describe but runs a pair of EL-34's.

I never see these things come up on ebay. :no:
 
I spoke with Phil at Heyboer today and he feels they can make one without reverse engineering the bad OPT, but he was running out the door when I called- so it will have to wait until tomorrow to get an answer.

kegger- it is funny that you mention the 210-E, when I did see any 210's on EBAY it was usually the 210-E or 210-F.

The 99 series OPT primary impedence seems to be to high for the 210-D which is 4.2K vs the 7.3K of the 99-D (as well as the 99-C).

Craig I can send some photos of the 210-D to you when I get a chance to shoot it. I actually planned on sending a photo to hhscott.com, since they do not have a picture of one. The 210-D has a similar face panel to the 99-B, and has more knobs due to the presence of the "dynaural bass suppresor" as you like to call it!!!

It uses 1614 tubes, and the entire power amp and power supply section are mounted horizontally- great fun to work on!!!
 
el-37 said:
I spoke with Phil at Heyboer today and he feels they can make one without reverse engineering the bad OPT, but he was running out the door when I called- so it will have to wait until tomorrow to get an answer.

kegger- it is funny that you mention the 210-E, when I did see any 210's on EBAY it was usually the 210-E or 210-F.

The 99 series OPT primary impedence seems to be to high for the 210-D which is 4.2K vs the 7.3K of the 99-D (as well as the 99-C).

Craig I can send some photos of the 210-D to you when I get a chance to shoot it. I actually planned on sending a photo to hhscott.com, since they do not have a picture of one. The 210-D has a similar face panel to the 99-B, and has more knobs due to the presence of the "dynaural bass suppresor" as you like to call it!!!

It uses 1614 tubes, and the entire power amp and power supply section are mounted horizontally- great fun to work on!!!

Okay now how do you know me LOL!!
 
"kegger- it is funny that you mention the 210-E, when I did see any 210's on EBAY it was usually the 210-E or 210-F."

I'll keep my eyes out, thanks!
 
Craig,

I took a peek at your website a while back..and saw the 296 rebuild...and your term for the DNS was pretty funny. I guess if one listens to 78's it might be useful.

I meant to ask you...can you give some listening impressions of the Soviet PIO caps that you currently use??? I have seen them on EBAY and am interested in trying them out.
 
el-37 said:
Craig,
I meant to ask you...can you give some listening impressions of the Soviet PIO caps that you currently use??? I have seen them on EBAY and am interested in trying them out.



For the price, they are rather good.

I use 0.1 uf K40Y-9 1000 volt coupling caps in my 2A3 amp, sounds good to me. Maybe someday I'll try them fancy copper caps.......


Should be real good blocking cap for a push-pull I would geuss.
I'm going replace the eight .1 mic General Instruments molded black death coupling caps in the Eico ST-70 with the K40Y-9.

Hope they don't leak...:sigh:
 
I love the Russian Mil Spec caps but like stated in another thread I don't believe they are PIO's. Some type of Film and Foils with oil. I've never seen paper that is basically clear, does not easily tear when oil soaked and melts when heated.

I would describe them a very smooth yet with great detail.

I've probably used 2000 of them without a single failure.


Craig
 
Back
Top Bottom