• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Subwoofer L and R input

Qoognish

Active Member
I just repaired a JBL 10" subwoofer that I'd like to use on my HT setup. It has L/R RCA low level inputs and standard speaker jacks for the high level in and out.

I only have a single RCA subwoofer out on my receiver. How is this designed to be hooked up?

Do I need to get an RCA 3-way "Y" cord to hook up the low level?

Can I go from the receiver front speaker outs > Subwoofer High Level in - then - from Subwoofer High Level out > Front speakers?
 
Register to hide this ad
It depends on what your manufacturer recommends. Safest bet is to get a Y cable, but in some cases the connection is "bridged" or connected or whatever so you can just plug the sub-out from the receiver into one of the RCA jacks. It's just a mono signal, after all. The downside in some cases is that features like auto-off might not work with only one connection. Again, it depends on the sub.

Of course you can also use the speaker-level inputs, but then I think you might lose some of the bass-control features of the amp (if you use them - crossover, etc.). So just make sure you set the crossover on the sub.
 
Most often just connecting to one input is all that is necessary. A "Y" cable won't hurt anything, but again, usually not necessary.

You could use the speaker level inputs as you described, but since you have a dedicated sub/lfe output on the receiver, that's what I'd use. And a single cable from there to one of the sub's inputs.

If you need a long cable a video cable with RCA ends works great for subs. No need to spend extra money on a "subwoofer" cable.
 
I use a Y cable on my Polk sub in the HT setup just make sure.
Regards,
Jim
 
Thanks all. I currently have it hooked up to one of the RCA inputs. It works, but I'm not getting much volume out of it. You'd think if I had the volume maxed out on the sub, it would be so boomy I couldn't take it. Instead, I need more volume.

The repair I made was simply replacing the popped capacitors. I'm positive they're the right caps and installed correctly. I'll try the Y cable.
 
Thanks all. I currently have it hooked up to one of the RCA inputs. It works, but I'm not getting much volume out of it. You'd think if I had the volume maxed out on the sub, it would be so boomy I couldn't take it. Instead, I need more volume.

The repair I made was simply replacing the popped capacitors. I'm positive they're the right caps and installed correctly. I'll try the Y cable.

Do you have the receiver configured for proper subwoofage?

Putting in the "Y" cable usually results in 3dB to 6dB more output with any given input signal level. Doesn't make the sub more powerful, just changes the gain structure.
 
Thanks all. I currently have it hooked up to one of the RCA inputs. It works, but I'm not getting much volume out of it. You'd think if I had the volume maxed out on the sub, it would be so boomy I couldn't take it. Instead, I need more volume.

The repair I made was simply replacing the popped capacitors. I'm positive they're the right caps and installed correctly. I'll try the Y cable.

The Y may help, but please remember all of these HT amps need to be setup correctly so that they are sending the correct signal out the LFE jack.

At his point, you aren't sure whether the sub is even working correctly.

Try connecting speaker wires from your speakers to the L/R high level input on the sub (naturally pull the RCA jack on the sub). Then configure your amp so that it "knows" there is no sub and should send a full signal to the front speakers.

With this setup you should be able to get way too much base. If you do, then you know the sub is OK and you need to mess with the amp controls to get more signal out the LFE jack.

Regards,
Jerry
 
Perhaps we should help ensure the setup is properly configured for the current setup, before the OP rewires the whole thing?

Post make and model of the receiver and make/model of rest of speakers for specific settings recommendations...
 
Subwoofer output levels can be deceiving, too. It's preferable to have an SPL meter if possible so you can measure precisely what's really going on.
 
Yes. Very true. A sub doesn't necessarily sound loud...depending on the scene content or the musical content.
 
Back
Top Bottom