• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

The Nikko 9095

Warren-Oates

One Dim Bulb
Subscriber
I bought one of these online recently and have been going through it. Thought I would post a thread on it as this appears to be a unit that does not have much information about rebuilding it posted on AK. I am no expert at rebuilding stereos or choosing parts, so if you see a glaring mistake please note it for the record here.

Overall I really like this receiver. Some things really standout; the slant faceplate (think Sansui 881), mostly solid metal control knobs (just a small plastic insert for ease of removal/installation), enclosed tuning gang, quite a bit of space inside for working on it, circuit breakers instead of fuses, the feet are big enough (I can actually get my fingers under the unit with the stock feet), PRE OUTS / MAIN INS, faceplate is thick and quite heavy, actual performance is promising.

Things I don't like; the did the pioneer SX-838 style power board - upside down under the sub chassis and the parts just bake away to a nice toasty blackness, tuner board again like the Pioneer SX-838 - it's going to be a real effort to get underneath it (but it's the only difficult board in it), speaker terminals a bit janky, I'll add more later if I find it.

The parts I use are based on information I read on AK, and some stuff on Digikey, just FYI
 
Register to hide this ad
First up was the bonnet, it was splitting, had some nicks, some corners ripped up. Wood glue, lots of clamps, glue mixed with sawdust for the chunks missing, some red oak veneer, Cabernet gel stain, and some rubbed fast drying oil poly. Brought it back to life. Caution when sanding this old dry plywood they used, it loves to make splinters that stab you, if your into splinters this wood is awesome.
 

Attachments

  • Bonnet_01_27_24.jpg
    Bonnet_01_27_24.jpg
    71.3 KB · Views: 41
  • Veneer 2.jpg
    Veneer 2.jpg
    105.6 KB · Views: 41
  • Veneer 3.jpg
    Veneer 3.jpg
    115.4 KB · Views: 41
The light here really shows the gel stain did not cover perfectly, the light area does not show as much in person, perhaps I should not have sanded to 600 grit before staining.
 

Attachments

  • BoN_Reveneer.jpg
    BoN_Reveneer.jpg
    163 KB · Views: 32
The wire mesh was rusting a bit, the screws holding it in were mostly rusted away so I had to dig them out. Took a brass brush to the mesh, probably would have been good to follow up with sandpaper after that but I did not. Some brass screws from McMaster Carr, and some nice extra angled bar installed for more support.
 

Attachments

  • Brass_Screws.jpg
    Brass_Screws.jpg
    159.2 KB · Views: 21
First board up was the power board, on it's way to being well done. Here some pics of power board, you can see where the voltage dropping resistors have made a heat island over the years.
 

Attachments

  • Baked_Power_Board.jpg
    Baked_Power_Board.jpg
    185.8 KB · Views: 62
  • Power_Board_Top_SHot.jpg
    Power_Board_Top_SHot.jpg
    181.8 KB · Views: 62
Parts I used for the Power Board (Protect Section)

Transistors:
Q951, Q952, Q955, Q957, Q958 were 2SC945(L) --> KSC1845
Q953, Q954 were 2SA733 --> KSA733
Q956 was 2SC1166(Y) --> KSC2690AYS

Diodes:
D951 was ZD XZ-122 --> this translates to a 12v 1/2 watt zener diode
D952, D953 were 1S1885 --> 1N4004

Relay:
Omron MY2-0-US 24VDC, --> a new Omron MY2 24VDC relay

Resistors:
R964 560ohm 2 watt, replaced with a 3 watt (stood off board even farther than factory)
R962 5.6ohm 1 watt, replaced with 2 watt ("")

Caps:
C953 tantulum 2.2uf, --> replaced with Kemet film 2.2uf
ecaps were replaced with various nichicon upw, panasonic fc, chemicon kzn caps, same uf no more than 1 notch up in voltage. ** Note C951 is a bi-polar ecap, and you will need a bipolar one to replace it, I used a 25v 22uf Nichicon.

Power Board (AMP Section)
Diode 922 and 923 - These are a common cathode diode array and a common anode diode array, they look like transistors but they are not. I replaced them some Taiwan Semi parts - UGF1005G (rated 300v 10a / Common Cathode Array), UGF1005GAH (rated 300v 10a / Common Anode Array)

Power Board (Tuner Section)
Transistor Q921 2SD235 --> KSD880YTU (added an extra wing to the sink)
Zener Diode D921 ZD WZ-130 --> replaced with a 1/2 watt 13v zener diode
Resistor R924 (labeled R923 by mistake in manual) 1/4 watt 6.8 ohm replaced with a new metal film just because it was in the bake zone
Resistor R921, R923 330ohm 2 watt, replaced with 3 watt resistors stood off best I could
Resistor R922 680ohm 4 watt, replaced with a 25 watt chassis mount resistor *thoughts in follow up post
ecaps replaced as above with suitable power board caps of the same uf / C922 C921

Large Axial cap on the board was replaced with a 1900uf 63V Kemet, original was 1000uf 63V. Choices are few here for a replacement if you want to stick with an axial cap.
 
To access the underside of the power board the easiest way I found was to remove one wire from a post, jumper post 12. The wire on jumper post 12 goes right over to the circuit breaker by the transformer and it is too short so you cannot rotate the board around with it attached. I unwrapped it so I could work on the board, when I finished I just soldered it back onto the post.
 

Attachments

  • Jumper_Post12_PowerB.jpg
    Jumper_Post12_PowerB.jpg
    135.2 KB · Views: 31
R922, the big daddy was generating some nice heat during my initial testing, I was getting 150 degrees on the hot end. This was under a 60W dimbulb for power, the unit upside down and the cover off in only 10 minutes. In other words the heat was free to rise up and escape, not like it would be under normal usage (think oven door closed). I decided to go with a 25 watt chassis mount, it sounds big but they are actually much smaller than you would think. I mounted it to the cross support bar that runs right next to the power board and transformer. A few holes tapped and some thermal compound, and there ya go. Takeing care of this one alone should help with keeping the other offenders under control.
 

Attachments

  • Chassis_Resistor_Mounted.jpg
    Chassis_Resistor_Mounted.jpg
    109.7 KB · Views: 28
While I had the power board up I drilled two holes in the chassis, right below where that baked area is. The extra air flow there should help with convection and further help to control heat. Here is a pic of the finished power board and a close up of the holes I drilled. Testing after completion the unit works nicely and the hottest temp I could measure after a few hours was 110 degrees on one of the 3 watt resistors. The chassis mount resistor never really heated up at all, as expected.

2_Holes_Drilled.jpgPbrd_Done.jpg
 
Nice work. Those modifications should help improve te reliability. At least the original design didn't place the electrolytics right next to the hot resistors, but that chassis mount approach should really help. Looking forward to seeing the rest of your restoration.
 
Parts I used for the Power Board (Protect Section)

Transistors:
Q951, Q952, Q955, Q957, Q958 were 2SC945(L) --> KSC1845
Q953, Q954 were 2SA733 --> KSA733
Q956 was 2SC1166(Y) --> KSC2690AYS

Diodes:
D951 was ZD XZ-122 --> this translates to a 12v 1/2 watt zener diode
D952, D953 were 1S1885 --> 1N4004

Relay:
Omron MY2-0-US 24VDC, --> a new Omron MY2 24VDC relay

Resistors:
R964 560ohm 2 watt, replaced with a 3 watt (stood off board even farther than factory)
R962 5.6ohm 1 watt, replaced with 2 watt ("")

Caps:
C953 tantulum 2.2uf, --> replaced with Kemet film 2.2uf
ecaps were replaced with various nichicon upw, panasonic fc, chemicon kzn caps, same uf no more than 1 notch up in voltage. ** Note C951 is a bi-polar ecap, and you will need a bipolar one to replace it, I used a 25v 22uf Nichicon.

Power Board (AMP Section)
Diode 922 and 923 - These are a common cathode diode array and a common anode diode array, they look like transistors but they are not. I replaced them some Taiwan Semi parts - UGF1005G (rated 300v 10a / Common Cathode Array), UGF1005GAH (rated 300v 10a / Common Anode Array)

Power Board (Tuner Section)
Transistor Q921 2SD235 --> KSD880YTU (added an extra wing to the sink)
Zener Diode D921 ZD WZ-130 --> replaced with a 1/2 watt 13v zener diode
Resistor R924 (labeled R923 by mistake in manual) 1/4 watt 6.8 ohm replaced with a new metal film just because it was in the bake zone
Resistor R921, R923 330ohm 2 watt, replaced with 3 watt resistors stood off best I could
Resistor R922 680ohm 4 watt, replaced with a 25 watt chassis mount resistor *thoughts in follow up post
ecaps replaced as above with suitable power board caps of the same uf / C922 C921

Large Axial cap on the board was replaced with a 1900uf 63V Kemet, original was 1000uf 63V. Choices are few here for a replacement if you want to stick with an axial cap.
Q951, Q952, Q955, Q957, Q958 were 2SC945(L) --> KSC1845 Should be KSC1815
Q953, Q954 were 2SA733 --> KSA733 Should be KSA1015

There are plenty of axial cap options, and I wouldn't have doubled that value. Why didn't you go up in voltage?
Here's a great 80V option.
 
As to the Axial cap, from what I have going read up a bit in UF on a power supply is OK. I sought the best specs I could find within reason.

The cap was Kemet:
PEG227MLQ4190QE4
Capacitance 1900 µF
Tolerance 10%, +30%
Voltage - Rated 63V
ESR (Equivalent Series Resistance) 47mOhm @ 100Hz
Lifetime @ Temp. 2000 Hrs @ 150°C
Ripple Current @ Low Frequency 2.52 A @ 100 Hz
Ripple Current @ High Frequency 7.2 A @ 5 kHz

The cap you note for sure would work, but is rated for 2000 Hrs at 85C, and has a higher ESR. Considering the location was in the hottest interior area I went with a cap that had a high temp rating and should have a long life there. Some of the caps I removed from the power board were browning and had cracks on the bottom from the heat, they were dried out husks. I would say my cooling efforts were successful enough that lower temp rated caps would have been fine on this board, I didn't really know how much cooler it would run, and I'm still not sure once it's back in it case and upside down how hot it will get there.

On the transistor subs you may be right, and thanks for your thoughts. By chance could you elaborate on your preferred choices in this area? One thing I will add to my gripes about this unit is that the schematic is devoid of voltages, in fact I found no voltages listed in the entire manual. I guess though there was nothing preventing me from probing the transistors with a meter and making a more informed decision.
 
The next board was the tone board. In hindsight it would have been better to start with the tone board, as the cross support bar needs to be removed to tilt the tone board out. Also it seemed easiest to loosen the circuit breaker behind it for clearance. I had to remove the cross support bar to install the chassis mount resistor, so I ended up having to remove it all over again to access the tone board, well a lesson learned.

Tone_Board_Tilted_Out.jpg
 
One other thing, there is an odd long thin metal tab that prevents you from tilting the tone board out. You have to reach in from the topside through a narrow opening and grab the tab with a doobie pliers and bend it up. Not sure what it's purpose is, you can see it has electric tape around the end, and it reaches around the black drum on the tone board (shield of some sort?). It's thin metal and it bends very easy.

Secret_Tab.jpg
 
With the tone board out it was a good time to address the large ceramic disc rf filter across the power switch. I replaced it with an actual snubber by Kemet, P409CP 150ohm / .01uf.

The Nikko 9095 has an integrated power switch, they are known to be flimsy in some units, but actually this one feels quite substantial and it's a full size rocker switch that has a very solid feel. Also it had what looked like an unused set of contacts on it. This one is working fine, so I just upgraded to a real snubber and should continue to live on.

snubber_replaced.jpg
 
The tone board is very easy to work on.

6 2SC1222 Transistors were replaced with KSC1845
4 ecaps .47uf were replaced with Kemet film caps
2 tantalum .47uf caps were replaced with Kemet film caps
2 ecaps 1uf were replaced with Kemet film caps
2 ecaps 16V 33uf were replaced with Nichicon UKT 25V 33uf caps

The Bass, Midrange, and Treble pots were desoldered from the board which allowed for nice access to blast them with CRC cleaner, it flush some yellow and brown residue. Let them dry and finished up with a bit of Deoxit F5. The controls are all the same, but each of mine had a number stamped on it, I noted the numbers and made sure to install them in the same spot they had come out of, if nothing else they should fit best in their original solder holes. I found the nuts that held the controls to the front chassis were not tight at all upon removal. Adjusting the controls sometimes left a hum on the left channel originally, plus the controls were scratchy of course. I sanded the chassis nice and clean where the nuts tighten down, cleaned up the nuts, and put a thin film of D5 on the nuts before snugging. Afterwards the controls are like butter, quiet, and no more hums. Noticeable improvement in sound quality through headphones as well.
 
Next up I did the lights, the faceplate was off so it was a good time to access the main dial lights. This unit is very easy to remove the faceplate, a long bar that comes out with a few screws secures the bottom of the plate, and the top is secured by 4 snap rivets. I pried the rivets up a bit with a razor blade, then they just pull out with fingers. Rivets cooperate nicely and you can re-use them. No glue, no double sided tape, just easy stuff. The dial lights are not in a straight line, they are slanted 45 degrees (so they fit a few extra in there), plain old 8v diallights.jpgled warm white fuse lights supply plenty of light and there appears to be no hotspots. However you will see my camera shot does pick up the hotspots, so they are there, very satisfied in person though with the look.
 
Function lights were replaced with 8v 4mm wired leds, spliced into exiting lines. 5mm would have been better, I had to add a layer of heat shrink tubing for tightness. I sanded them, but on the longer bays they don't provide perfect coverage, in the future I might try two leds in the longs bays with some dimming of the lights. Also overall the leds in the function lights are a bit too bright, I may look into dropping the voltage just a bit. Lovely brilliant yellow through the dial face though, previous was sickly orange. I replaced the stereo light with an 8v inc., since I was in there I just did it, of course it stayed sickly orange. To get at the function light just remove the bar below the dial string, 2 screws, plenty of room and access.

graybar.jpg
 
Lastly the meter lights, one screw and you move the heavy metal cage they are in, replaced with simple ww 8v led like the dial lights. You can see the bulb is the bigger torpedo type, all of the lights are like this. You have to squeeze the fuse holders before installing the leds, as the new leds are a bit slimmer. Here's a shot of old and new so you can see the difference.

IMG_20240211_182328.jpgIMG_20240211_181551.jpg
 
Back
Top Bottom