• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Thorens TD 520 speed issue.

Montycat

Moderator
Staff member
Moderator
Subscriber
So far I haven't been able to find a good resource on this. I have my first TD-520 on the bench. It has a 12" SME arm on it and looks great.

There are a few things that won't be hard to fix, such as a badly done splice on the RCA cable, a strobe mirror that has fallen off and a broken anti skate thread.

The speed however is a problem. With no load the motor seems to run at the proper speed but as soon as the belt is on and turning the platter it barely moves. It is faster on 45 and even more so on 78 but might be only about a third of the speed it should be. The external pitch control the as some effect but not much.

I see 3 pots on the circuit board but other than labels of P1, P2 and P3 I don't know their function. P2 is closer to the top mounted control than the others and perhaps it's also speed related but I don't want to mess with it without knowing.

It could be a torque issue with the motor too.

I'll upload some pics later. I have a very slow connection here.
 
Register to hide this ad
I've downloaded and even printed the schematic but the resolution is very bad and can barely be read. I see what look like variable resistors but can't read the labels.

10419.jpg
 
I've downloaded and even printed the schematic but the resolution is very bad (...)

I've downloaded one TD 520/521 service manual from AudioCircuit and another from VE yesterday, hoping that I could offer some help, but both turned out to be just the same lousy copy (regarding the resolution of the schematics) - and while there's yet another on Elektrotanya, that doesn't differ in file size, so that I'd bet it to be the same again.

Should be possible to identify, which trim pot is which, from comparing the schematic with the actual circuitry, though - but I couldn't find enough or respectively sufficiently good pics of the board (especially of its rear side) to help you with that.

Greetings from Munich!

Manfred / lini
 
I've downloaded one TD 520/521 service manual from AudioCircuit and another from VE yesterday, hoping that I could offer some help, but both turned out to be just the same lousy copy (regarding the resolution of the schematics) - and while there's yet another on Elektrotanya, that doesn't differ in file size, so that I'd bet it to be the same again.

Should be possible to identify, which trim pot is which, from comparing the schematic with the actual circuitry, though - but I couldn't find enough or respectively sufficiently good pics of the board (especially of its rear side) to help you with that.

Greetings from Munich!

Manfred / lini

Thanks Manfred!

Actually I found that the second version of the SM at VE at least has some text describing the functions and circuit. Using Google's Translate function I might have found what I need. Below is a portion of that translation. I'll try the rest another time from my PC and not my phone.

hfe_thorens_td520s...

:

Switchable voltage dividers are located at their inputs. Depending on the selected speed, these dividers reduce the charging values for the capacitors, thus electronically reducing their values.

This elaborate method of speed switching was chosen so that the 2 x 100 kΩ potentiometer for speed adjustment has approximately the same control range for all speeds.

The four complementary output stages T100-T101, T102-T103, T105-T107, and T104-T106, still visible in the circuit diagram, supply the power for the motor. Two amplifiers each feed one motor winding in a bridge circuit.

The fourth output stage required for this, T104-T106, is not included in the generator. The operational amplifier from IC 207 that feeds it generates the necessary phase relationship.
 
(...) This elaborate method of speed switching was chosen so that the 2 x 100 kΩ potentiometer for speed adjustment has approximately the same control range for all speeds. (...)

This would refer to the externally attached pitch pot, though - rather than to the trim pots, two of which would also appear to be part of the two-phase generator circuitry (while the third obviously is involved in the auto-stop funtion - and according to the instructions for the auto-stop adjustment, that one should be P3).

Greetings from Munich!

Manfred / lini
 
Right. That's what I thought; it was regarding the top mounted pitch pot.

Also in other parts of the quoted/translated document it refers to some test point voltages so I am going to go down that path.
 
(...) Also in other parts of the quoted/translated document it refers to some test point voltages so I am going to go down that path.

Might be a good idea to replace the three elcaps (especially the two in the power supply section), before you dig in more deeply. Often enough the elcaps are pretty much dead by now on the boards for the TD 316/318/320/321s and the TD 280s, so I'd expect the same in case of the TD 520/521s.

Greetings from Munich!

Manfred / lini
 
I'm beginning to think that it might be an issue with the clutch in the motor pulley. I disassembled it yesterday and saw no obvious issues but perhaps I need to replace the felt or something.

10487.jpg
 
Back
Top Bottom