• The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html

New profile posts

What's new Featured content New posts New media New media comments New profile posts Latest activity
Rob357
Hi Ray, I love the vp-7725D on your bench. The price is far more than I can justify. Is there a distortion analyzer that you would recommend? One channel is OK. The Sound Technology 1700b I have is not working, obsolete op amps are not helping!
Ray Gianelli
Ray Gianelli
If I had it to do all over again I'd go with the QuantAsylum QA-403.
  • Like
Reactions: Rob357
B
New Member,
hello everyone, my name is Matt and I am back to listen to records again. took a little hiatus. got a lot of records in the meantime. I purchased a Sony ps3300 turntable from 1976 and I'm looking for some parts or a part so I figured I'd look on here and maybe check out some other stuff while on going about that. it'll be nice to talk to people here. thanks!

Attachments

  • PXL_20260222_195715420.jpg
    PXL_20260222_195715420.jpg
    119.7 KB · Views: 2
J
Aha! Trace on the pcb going to right channel tape monitor is cracked. Also it is right next to the item that was suggested to check voltages on, no voltage on the 2 legs. Can I just solder a jumper wire to bypass the trace?1000002320.jpg
Buck Rogers
Buck Rogers
Yes, Trace it back to a thicker part then solder a flexible jumper wire to make connection.

Then take some epoxy and use it to afix the broken board.
D
Hi! New old guy here..Just paired a Marantz 1060 & original small advents ;could not believe the sound .Guess I've been listening to digital stuuff too long.Later.
R
hi there. Saw an old post of yours about a NAD 705 with a tuner problem. I have one with the exact same problem. I have to disconnect the 5V from the tuner board connector to get it to power on. Do you think the LM7000 was the problem with getting the power on? Where did you buy the chip? Any help would be appreciated.
T
I am working on a Phase Linear 4000 pre amp and it was working but had low level noise now it’s dead no sound and it’s kicking my butt
total recap and original jack’s added as well as all connections repaired
I have signal going to the source sel and not getting it at the volume control I hope someone can help me on where to go next
T
Need a schematic for a Heathkit AR-1650 stereo receiver.Can’t seem to have any luck.Tech says he needs a schematic in order to repair it.
M
I've been trying to get my Onkyo TX-8500 to function on both driver boards and I found a quote from you in 2018. Thank you for helping me to know that the right driver board IS the right channel. I've replaced all the components but the right is still not working.
flatwound
Second room is an Technics Sl-Q5 with a Grado Green3 p-mount / Schiit Mani2 / Yamaha 500 Avantage receiver / Klipsch Forte (original, or 1 if you must)
flatwound
Currently using an AT33ptg/ii into an AT moving coil step-up Mk10 into the moon lp3 set to mm mode.
D
Hi mboxler: the discussion from others in the thread about the Super H, point to you about the back cover plate file that you developed. Any chance I can obtain a copy? Im in the front end of doing a mod to the H2 and was going to hand craft one out of 1/4 MDF since its not very large. Thanks!!
View previous comments…
mboxler
mboxler
Cool! Send me your email address and I'll send you the file. Let me know what file format you prefer.

Mike
D
davekrys
I posed the question to the makerspace and will get right back to you. My email is davidjbrown321@gmail.com Since youve done this before, do you have a prefered material to use?
D
davekrys
Mike: Here's what they said: Dxf file if you can. If not, sometimes we can convert a pdf or an image as long as we know exact dimensions for every line.
david
G
Good evening, I was referred to you by ChatGPT. I’m looking for warm white light kit for pioneer sx-680 and sx-750. If you don’t have can you lead me in the direction to find these?
rshep
Good morning. I just saw the KA7100 and I'm very interested. I love that Kenwood era, I had KD1030 cassette deck and KD500 turntable for years and thought they were brilliantly designed.
I live in Ahawaukee which should make this an easy transaction. Let me know how we should proceed. Best Regards, Rob (602) 715-6471.
Back
Top Bottom