Good evening, the reason for contacting you is that in the past you posted schematics and parts list for a RCA RS-199B tube amp. I am unable to read clearly the copies you posted and was wondering if you still had copies that were sharper I can obtain from you? Thank you
New profile posts
Retired and listening to music
Avionic: For starters thank you for your service! I have posted an issue with my MX-1000 here:
Any and all assistance you can provide would be greatly appreciated!
If I can't get it I may end up sending it to you if you are still doing this type of repair.
Thanks!
Any and all assistance you can provide would be greatly appreciated!
If I can't get it I may end up sending it to you if you are still doing this type of repair.
Thanks!
-
Rob357 Ray Gianelli Rob357 wrote on Ray Gianelli's profile.
Hi Ray, I love the vp-7725D on your bench. The price is far more than I can justify. Is there a distortion analyzer that you would recommend? One channel is OK. The Sound Technology 1700b I have is not working, obsolete op amps are not helping!
New guy
New snd hoping to get help finding a part for a turntable that is out of production
New Member,
hello everyone, my name is Matt and I am back to listen to records again. took a little hiatus. got a lot of records in the meantime. I purchased a Sony ps3300 turntable from 1976 and I'm looking for some parts or a part so I figured I'd look on here and maybe check out some other stuff while on going about that. it'll be nice to talk to people here. thanks!
hello everyone, my name is Matt and I am back to listen to records again. took a little hiatus. got a lot of records in the meantime. I purchased a Sony ps3300 turntable from 1976 and I'm looking for some parts or a part so I figured I'd look on here and maybe check out some other stuff while on going about that. it'll be nice to talk to people here. thanks!
Attachments
Aha! Trace on the pcb going to right channel tape monitor is cracked. Also it is right next to the item that was suggested to check voltages on, no voltage on the 2 legs. Can I just solder a jumper wire to bypass the trace?
hi there. Saw an old post of yours about a NAD 705 with a tuner problem. I have one with the exact same problem. I have to disconnect the 5V from the tuner board connector to get it to power on. Do you think the LM7000 was the problem with getting the power on? Where did you buy the chip? Any help would be appreciated.
I am working on a Phase Linear 4000 pre amp and it was working but had low level noise now it’s dead no sound and it’s kicking my butt
total recap and original jack’s added as well as all connections repaired
I have signal going to the source sel and not getting it at the volume control I hope someone can help me on where to go next
total recap and original jack’s added as well as all connections repaired
I have signal going to the source sel and not getting it at the volume control I hope someone can help me on where to go next
Owner of a Fisher '66 Philharmonic (P-291).
Air Force Avionics tech '76-'78
Air Force Avionics tech '76-'78
Taking repairs on a limited basis based on my interest in the gear
-
M
MyHeresyIsMe z-adamson MyHeresyIsMe wrote on z-adamson's profile.
I've been trying to get my Onkyo TX-8500 to function on both driver boards and I found a quote from you in 2018. Thank you for helping me to know that the right driver board IS the right channel. I've replaced all the components but the right is still not working.
Second room is an Technics Sl-Q5 with a Grado Green3 p-mount / Schiit Mani2 / Yamaha 500 Avantage receiver / Klipsch Forte (original, or 1 if you must)
Currently using an AT33ptg/ii into an AT moving coil step-up Mk10 into the moon lp3 set to mm mode.