calibration
-
T
Ps x800 owners, how close is your tracking force scale adjustment to the actual tracking force ?
I am recalibrating my ps x800 and I got it pretty close (atleast I think), I have it to within around 0,10 grams error margin on every weight setting except 3 grams (which is at 0,20 error margin). I have been fiddling with it for quite a while and I am pretty much satisfied as is, but I would...- TrevorBarten
- Thread
- biotracer calibration repair sony ps x800
- Replies: 2
- Forum: Turntables
-
Calibration Problem
Hello, I have restored my Akai GX-600DB. It works just fine except for calibration. I have tried to calibrate it with the audition's tone generator. When I calibrate it according to high speed works well, but when I try to use it at low speed, all calibration goes away... I expect calibration... -
B
Good Nakamichi calibration service in Portland, OR
Hi, I'm new here and this is my first post. Great forums! About a year and a half ago I decided to dive back into tapes after almost 25 years. After recovering from the sticker shock for used gear and NOS tapes, I started looking for good deals in the low-to-mid range Naks. Currently I have... -
Kenwood KR-6600 restoration etc.
I have been working on this Kenwood a lot of this week. A friend sold it to me cheap, as it was stuck in protect mode... I kind of listened in on the amp section and heard that there was a lot of noise from bad transistors, in this case it was the 2sa733's as the differential pairs and others...- sean sweeney
- Thread
- analog bias calibration kenwood kr-6600 receiver restoration setting transistors vintage
- Replies: 7
- Forum: Kenwood-Trio/Kensonic-Accuphase
-
Aiwa ADF 810 Calibration
I have this Aiwa deck-it makes very good tapes. I have set levels by ear more often than not. When I look at the User Manual, it is so cryptic about calibration. Primarily, there is a process to set a level-with a corresponding "Rec Sensitivity" trim knob, but after reading multiple times, I...- oldvinyldude
- Thread
- aiwa adf810 calibration rec sensitivity
- Replies: 5
- Forum: Tape
-
Vintage Velodyne ULD-15 Subwoofer Problem!
Hello All, You may scoff but yes, I am still using a vintage Velodyne ULD-15 subwoofer from 1986 in my home theater setup. Two years ago I refoamed the woofer, as the surround had deteriorated after not using it for many years. This Velodyne definitely works fine and adds nice bass in my 12' x... -
Technics RS 1500 Rewind Issue.
I have a Technics RS 1500us. Rewind all but stalls out near the end of the Rewind process with 7" and 10.5 Inch. Fast Forward works fine. I've swapped the Supply and Take-Up Reel Tables to see if it's that and to eliminate the Reel Table Board was possibly the issue. No change. I've recapped... -
J
Stark 9-66 tube tester calibration help needed
Hi, I recently purchased a Stark 9-66 Tube tester and have the one page tube tester test and calibration procedure, but the Plate and Cathode AC Voltage Checks come up with no voltage. I tested a few tubes and they seem to test, but I am not sure of the accuracy. I am looking for some help...- Jeff Turner
- Thread
- calibration hickok 533 stark 9-66 tube tester
- Replies: 3
- Forum: DIY
-
Tube tester precision 612
Hello. I recently bought my first tube tester, a Presicion 612. It seems complete, but i am expectant about doing it work. Well, as i read in other site, first is calibration, in order to that, resistors must be replaced. I have got the user manual and calibration procedure via...- jFF_Bulbo
- Thread
- calibration presicion tester tube vintage
- Replies: 6
- Forum: Tube Audio