• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Realistic Optimus 1

nadude98

7MGTE Power!
Does anyone know the part number for the tweeters in the Optimus 1, the original not the 1b. There is no part number on the ones in the speakers.
 
Register to hide this ad
There were changes to Optimus 1 during its production run including different tweeter versions (prior to Optimus 1B). The earliest Optimus 1 apparently used alnico magnet drivers. One has been identified in these forums as part no. 0701:

0701 alnico r.jpg

Expect these to be very rare.

Another model seen is 0705Aa (not 0705Ae from Optimus 1B / Nova 7B):

tweeter 0705Aa.jpg

Optimus 1 started in 1968 as catalog no. 40-1969. At some point it became cat. no. 40-1969A, and there may even be a 40-1969B. Each of these indicates some design change, if only minor.
 
There were changes to Optimus 1 during its production run including different tweeter versions (prior to Optimus 1B). The earliest Optimus 1 apparently used alnico magnet drivers. One has been identified in these forums as part no. 0701:

View attachment 2731884

Expect these to be very rare.

Another model seen is 0705Aa (not 0705Ae from Optimus 1B / Nova 7B):

View attachment 2731885

Optimus 1 started in 1968 as catalog no. 40-1969. At some point it became cat. no. 40-1969A, and there may even be a 40-1969B. Each of these indicates some design change, if only minor.
Both are 16 ohm. I wonder if the crossovers are the same? If so, either should work I would think. The change may have just been a supply thing.
 
Thanks for the reply. The ones in it look like they second one. They have a plastic insert behind the speakers to isolate it acoustically while it looks the the top one is built to isolate it. 16ohms makes sense. I have not hooked up anything to except a meter to test impedance and it was all over the place varying from 0 ohms to 16 ohms to open. I think the tweeters still in them are bad.. Darn. That would mean I need 4 of them if so.
 
Both are 16 ohm. I wonder if the crossovers are the same? If so, either should work I would think. The change may have just been a supply thing.
@nerdorama has shared insights into some driver variants and crossover differences. He notes small variations in capacitor and coil values, and even attenuation resistors. Though value differences don't seem to fall much outside of each other's tolerances.

Original Optimus 1 was designed for power handling typical of the 60's. With receiver power wars of the '70's taking its toll on speaker systems, Tandy responded by beefing up their drivers. 1975 introduced "B" models featuring tweeters with aluminium voice coils to address the issue.

AL VCs.jpg

Losses to the carnage have contributed to increasing rarity of original tweeters.. If they can't be found, "B" model 0705Ae tweeters are practical replacements that preserve closest fit, performance and appearance to the originals. As long as they remain available ...
 
I wonder how badly the sound would be affected if using a 8ohm 5 watt resistor in series with a 0705Ad 8ohm tweeter?
Far from ideal I know..
Trying to fix a pair of Optimus1 speakers for a friend, they were his mom's so it is about sentimental value rather than just buying another set of speakers or something. He doesn't remember who, but someone replaced one tweeter in each speaker with mismatching ones and the plastic cups for them are missing.20221205_195031_HDR.jpg 20221205_195111.jpg 20221205_195103_HDR.jpg
 
I wonder how badly the sound would be affected if using a 8ohm 5 watt resistor in series with a 0705Ad 8ohm tweeter?
An 8Ω series resistor will attenuate output of the 0705Ad mid/tweeter. Depending on how it's sensitivity compares to the 16Ω unit, HF to LF output balance could be affected. You can always pop one in and experiment.

If your crossovers are still stock, and match the one @nerdorama traced out, three series resistors in the HF Compensation switch add up to 8Ω in the "Low" setting:
Optimus-1 ceramic.png

You could try installing the 8Ω tweeter and reroute the + lead of the 16Ω tweeter to bypass all resistors.

balance_1.png

HF comp set to "Low" puts 8Ω in series with the 8Ω tweeter where output can then be compared with the raw 16Ω unit to see if they are close to a match. If the 8Ω tweeter isn't keeping up, try HF Comp. at "Normal" for 4Ω in series with it. That puts total mid/tweeter load impedance at roughly 6Ω -- nothing crazy.

If a setting is found where tweeters' output are close to each other but total HF is too low to balance with LF, then the mod is not going to work well. If total tweeter output is hotter than LF, just bring it down with a bit of series resistance.

An open-back 0705Ad will still need an isolation cup, which can usually be found on ebay. Though one could be borrowed from the other speaker for experimentation.
 
I thought that the originals were 16 ohm tweeters in parallel and the b models used 4 ohm tweeters in series, but it's been years since I owned either pair and my memory isn't always reliable.
 
Back
Top Bottom