• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Wharfedale Owners Thread

Hello again, when I uncovered my Rosedales I noticed that the crossover coils were only wrapped in a colored ribbon, but there are no values anywhere.

Could you show me a picture of the crossover of your W70-E?

Could you tell me the values of the coils?

Could you show me your schematic drawing?

Thank you very much

As promised, schematic for the W70E crossover.
Hope this image file comes through OK. BTW all resistors are 5W including the potentiometers.
Wharfedale Crossover.png
 
As promised, schematic for the W70E crossover.
Hope this image file comes through OK. BTW all resistors are 5W including the potentiometers.
View attachment 1297708

Hello, definitely the xover are different, the xover of my Rosedale are like the ones that appear in the photo ... (the photos were uploaded by another user to the forum)
but it can be clearly seen that both the coils and the scheme are different.

COILS.png

XOVER.png
 
The crossovers in a pair of Rosedales I have are like those above too. Far different than the two pairs of earlier W70's I have.
 
Hello, definitely the xover are different, the xover of my Rosedale are like the ones that appear in the photo ... (the photos were uploaded by another user to the forum)
but it can be clearly seen that both the coils and the scheme are different.

Sorry, I somehow thought you had the newer version of the W70E. Have you looked on other audio forums to see if anyone else has the answer to this?
 
My Rosedale restoration project so far.... just when you think you've checked all the boxes something new pops up that you didn't expect. I rebuilt both crossovers, patched one of the 15 inch woofers, stabilized and built up crumbling MDF and did two veneer patches, ordered an original replacement for the other woofer on ebay, modified two DT94 4 Ohm tweeters to match original size and mounting (used resin casting to extend the size and fill original mounting holes).

Today I put everything back together to see how they sounded. Oddly enough the woofer I patched sounds great, but I found the one I ordered on ebay has some issues where the rubber surround has come unglued from the paper (created a buzzing noise on certain base notes). Nothing I can't fix, but it's another brick in the pile. Also found yet another small piece of missing veneer near the back on the bottom trim. With each iteration, I'm getting closer to cleaning, sanding and reapplying new oil finish.
 
My Rosedale restoration project update. Got the woofer fixed and played a variety of music to see what they could do, and frankly, was blown away. My only complaint is they can't take a lot of power. I lthink they are better than the KLH Model 5's - better sound stage and presence.
 
Hello, definitely the xover are different, the xover of my Rosedale are like the ones that appear in the photo ... (the photos were uploaded by another user to the forum)
but it can be clearly seen that both the coils and the scheme are different.

I don't think the schematic for your tweeter is correct. I believe you will find the inductor goes from the "+" terminal (on the tweeter) to ground to shunt low frequency. The mid range makes sense as the inductor will roll off the highs and the cap will roll off the lows leaving a mid-band for the mid range speaker (this and the woofer are typical 6db/Octave crossover). The tweeter I think is 12db/Octave. I was wondering if you have a college near where you are that has an electronic lab? They would probably have to equipment you need to measure the inductors.
 
Last edited:
I don't think the schematic for your tweeter is correct. I believe you will find the inductor goes from the "+" terminal to ground to shunt low frequency. The mid range makes sense as the inductor will roll off the highs and the cap will roll off the lows leaving a mid-band for the mid range speaker (this and the woofer are typical 6db/Octave crossover). The tweeter I think is 12db/Octave. I was wondering if you have a college near where you are that has an electronic lab? They would probably have to equipment you need to measure the inductors.


I will get to take pictures of my crossover to compare.
 
As promised, schematic for the W70E crossover.
Hope this image file comes through OK. BTW all resistors are 5W including the potentiometers.
View attachment 1297708

Hi again, could you show me pictures of your W70E? I would like to know if my Rosedale have the same components as your W70E ...

I do not discard the idea of redoing the xover based on your diagram, but for that I need to make sure to have the same components.

Regards!
 
Hi again, could you show me pictures of your W70E? I would like to know if my Rosedale have the same components as your W70E ...

I do not discard the idea of redoing the xover based on your diagram, but for that I need to make sure to have the same components.

Regards!
I can tell you the difference without even having to do this. You have an earlier version of the W70E, and your speakers are rear mounted on the baffle. The back on your speakers probably has screws that let you access the parts inside. Mine were built two to three years later. The back is completely sealed, and the speakers are all flush mounted on the front baffle. The only way into the cabinet is by taking out the woofer. My mid range has its own mini-enclosure to prevent the sealed box from disturbing it. The speaker components used in both of these configurations is the same. Again, my inclination would be to keep the crossover as original as possible. These are antiques after all, and reflect the technology of the times
 
I can tell you the difference without even having to do this. You have an earlier version of the W70E, and your speakers are rear mounted on the baffle. The back on your speakers probably has screws that let you access the parts inside. Mine were built two to three years later. The back is completely sealed, and the speakers are all flush mounted on the front baffle. The only way into the cabinet is by taking out the woofer. My mid range has its own mini-enclosure to prevent the sealed box from disturbing it. The speaker components used in both of these configurations is the same. Again, my inclination would be to keep the crossover as original as possible. These are antiques after all, and reflect the technology of the times


Hello again, sorry to insist, but I just want to know if the components of your W70E are exactly the same as mine, at least with the naked eye.

My doubt is that I have seen pictures of many W70E models that use a woofer with a black border, while the edge of the woofer of my rosedale is green. Another thing that strikes me is the mid-range, which is clearly different from my Rosedale.

I leave the pictures of my Rosedale, and also I leave you one of a W70E model that I found in google so you can see the differences.

I appreciate your help and apologize for insisting. Thank you.

204224bdc9d7cd8575bf12243ed7dc71.jpg


4417d5c6dcced089a5e2d9d862c54d1b.jpg


fa5d49a3264dd3d50fdea302ac197e2d.jpg


here the difference

f6988779ac3c4bf588b2e042cb341273.jpg
 
Hello again, sorry to insist, but I just want to know if the components of your W70E are exactly the same as mine, at least with the naked eye.

My doubt is that I have seen pictures of many W70E models that use a woofer with a black border, while the edge of the woofer of my rosedale is green. Another thing that strikes me is the mid-range, which is clearly different from my Rosedale.

I leave the pictures of my Rosedale, and also I leave you one of a W70E model that I found in google so you can see the differences.

I appreciate your help and apologize for insisting. Thank you.

204224bdc9d7cd8575bf12243ed7dc71.jpg


4417d5c6dcced089a5e2d9d862c54d1b.jpg


fa5d49a3264dd3d50fdea302ac197e2d.jpg


here the difference

View attachment 1303410

Mine look exactly like the bottom picture you posted from the web. I don't think the color of the gasket being green is of any consequence since it uses the same rubber surround on the speaker cone itself. The tweeter is also the same, but yours looks like it's mounted a little closer to the mid range speaker.
 
Mine look exactly like the bottom picture you posted from the web. I don't think the color of the gasket being green is of any consequence since it uses the same rubber surround on the speaker cone itself. The tweeter is also the same, but yours looks like it's mounted a little closer to the mid range speaker.

I think it's excellent, you clarified many of my doubts ...

definitely the mid-range is different, I'll have to look for the schematic drawing of some crossover that uses this mid-range

Thank you !
 
My Rosedale W70E's all put together - some pictures for anyone who's interested. The first pic shows the worst cabinet which had to have 3 veneer patches: bottom left molding was missing a strip of veneer about 8 inches long. IMG_3164.jpg IMG_3165.jpg The second patch was on the top. The third patch was very small and on the molding on the right side (not shown). Cabinets were cleaned with mineral spirits and then lightly sanded to remove scratches. Dents were steamed out where possible. I used artist oil color to even out the color a bit on the veneer patches. Three coats of oil finish later and now they look like this: IMG_3179.jpg IMG_3186.jpg
Can you see the veneer patch on the top?IMG_3181.jpg

You can see my tweeter replica made with a DT94 (originally 3.7 inch OD) with polycarbonate dome. I used resin casting to make them 4.25 inches and drilled the holes to match original mounting. I have since acquired a replacement for one of the bad original tweeters, but I think I will run with these for now. If someone wants to put them back to original someday I will have the parts.
IMG_3196.jpg
 
My Rosedale W70E's all put together - some pictures for anyone who's interested. The first pic shows the worst cabinet which had to have 3 veneer patches: bottom left molding was missing a strip of veneer about 8 inches long. View attachment 1310672 View attachment 1310674 The second patch was on the top. The third patch was very small and on the molding on the right side (not shown). Cabinets were cleaned with mineral spirits and then lightly sanded to remove scratches. Dents were steamed out where possible. I used artist oil color to even out the color a bit on the veneer patches. Three coats of oil finish later and now they look like this: View attachment 1310664 View attachment 1310670
Can you see the veneer patch on the top?View attachment 1310667

You can see my tweeter replica made with a DT94 (originally 3.7 inch OD) with polycarbonate dome. I used resin casting to make them 4.25 inches and drilled the holes to match original mounting. I have since acquired a replacement for one of the bad original tweeters, but I think I will run with these for now. If someone wants to put them back to original someday I will have the parts.
View attachment 1310683

very nice!
 
Just ordered some Tung oil. This is pure unadulterated Tung Oil from Real Milk Paint Company. I have used their Tung oil before on gun stocks wonderful stuff. Pure Tung Oil is such a pleasure to work with. I’ll use it to seal up the wood on the W45’s.

8D54B0F2-F536-4EF4-B5B8-376CA27DCFDB.png

3AF22CBD-8215-4FC8-8F67-B4FF932E3FE7.jpeg
 
We're did you purchase the veneers that is exactly what I need for my W35’s.
I think I mentioned this before, Rockler Woodworking has veneer packages. There are other national chains that may carry veneer in your area. If you can find a brick and mortar store near you the best thing to do is is go there and find a package that has the closest match. Walnut veneer is highly variable - a visual match is the best way to go if you can. Also, I did my speakers with Tung oil as well. It works great, but make sure to do at least three coats and lightly sand the entire cabinet with 220 grit to remove any raised grain.One more tip, pick up a tube of artist oil color "Burnt Umber" will give you a good walnut color. Apply just before you start oiling - use this only to even out the color on any veneer you add or to darken areas that you had to sand heavily. Apply direct to get the darkest result and wipe excess with paper towel; use your fingers to blend. If you make a mistake most of this can be washed off with mineral spirits.
 
Back
Top Bottom