• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Show me your workbench!

i just finished building my new work bench


008_zps6fc895db.jpg


005_zps5e9d1f15.jpg


006-1_zps53e06ff8.jpg


007-1_zps80c613bb.jpg
 
What in gawd's name is that yellow monstrosity on the lift?

It's so ugly, it's beautiful!! <G>
 
Thanks Ski. It is the Industrial Motor Bike. I built it a couple years back. Click on my website link and go to Vehicle Art. There are more pix there.
 
I have one set up for very low frequency stuff and the other for higher feq. It is easier to have two mainframes than to swap the plug ins. Most of the equipment I got for dirt cheap because it was not working at the time. Luckily that old equipment was pretty easy to repair. Not like the newer stuff that is all micro-processor based with custom I.C.s.

So, what's in the 182T mainframe? Also looks like you have a Tektronix spectrum analyzer as well? That makes 4?
 
So, what's in the 182T mainframe? Also looks like you have a Tektronix spectrum analyzer as well? That makes 4?

I have two HP141T mainframes. One with the very low freq plug ins (can see audio freqs if you try real hard) and another for 'RF' frequencies. The other CRTs are o'scopes. The one on the left next to the ST1700B distortion analyzer is a cheap 20MHz Leader that I bought new back in the early '80s. I keep it more for sentimental reasons than anything else. Wow, how many people get sentimental about an o'scope? It works well for monitoring the input signal and distortion signal from the distortion analyzer. Above it is a nicer 225MHz HP scope that is the one I mostly use for troubleshooting. The one on the right with the big blue screen is a very old 50MHz (I think) that rarely gets used. But I like it because it has such a nice large, bright display.
I got most of the equipment from a company I worked for that closed its doors. They had a lot of old non-serviceable equipment stacked up and sold it for salvage. Most of it was very easy to repair. The service manuals for the old HP stuff is very detailed and most of the parts are discrete. Not a lot of the custom I.C.s that end up being the demise of newer equipment. But that being said, I sometimes seem to spend as much time working on my old test equipment as I do working on anything else. I recap'd the 141T mainframes by cutting open the big metal chassis mount filter caps and installing series or parallel combinations of caps to get to the correct volatge and capacitance, then glueing the can back together.
I just finished recapping the four bench top DMMs and then tweaking the calibration using a meter I borrowed from my 'day job' as a reference.

Terry
 
My new project bench
IMG_2589.jpg


and what good is an empty project bench?
IMG_2592.jpg


Work area is to the left, it's a blender cart from the thrift store
Guess I really ought too take a better pic of that area
 
shop/mancave

I got it about 50 percent finished, I need to panel the west end and rebuild the swing doors. There's a lean-to on the side of the shop that we used to use for horses. I'll enclose that for storage
 

Attachments

  • 0226131136.jpg
    0226131136.jpg
    80.7 KB · Views: 305
  • 0226131137.jpg
    0226131137.jpg
    94.5 KB · Views: 273
  • 0226131137a.jpg
    0226131137a.jpg
    85.3 KB · Views: 219
  • 0226131137b.jpg
    0226131137b.jpg
    72.2 KB · Views: 221
  • 0226131138.jpg
    0226131138.jpg
    79.3 KB · Views: 238
Show me your work bench and I'll show you someone who graduated SHOP class with HONORS--(that wasn't me, BTW)! lol

cnh2
 
Built this workbench many moons ago when I did a lot of woodworking.Made from solid maple,all mortise and tenon.The wife thought it was a perfect place to pot plants,so there was some staining on the top.

 
Back
Top Bottom