• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Subwoofer/amp issues

mattcknz

New Member
I recently got my subwoofer out of storage and decided to give it a try in my stereo system. Wow , it makes a big difference!
I currently have a denon reciever as my main amp although i can see this changing to a tpa 3116 in the near future.
I have found that it will not output anything to the subwoofer over the subwoofer out when fed an analogue signal. If i hook it up to the tape out then the subwoofer recieves a signal but the volume control has no effect so its just hopeless if I am altering the volume - I have to get up and fiddle with the subwoofer again to get the volume correct.
Is there a solution to this that will work also if i go to a 3116,or am I now in the market for a new amp.
 
Last edited:
Register to hide this ad
Make sure your main speakers are set to "small" on the receiver. If they are set to large, it may be disabling the sub assuming the main speakers dig low enough on their own.

This is the case on my Marantz AV receiver. And I know other manufacturers use the same concept. Your Denon may or may not have this setting.
 
Make sure your main speakers are set to "small" on the receiver. If they are set to large, it may be disabling the sub assuming the main speakers dig low enough on their own.

This is the case on my Marantz AV receiver. And I know other manufacturers use the same concept. Your Denon may or may not have this setting.

Yep, my Pioneer AV receiver is the same way too.
 
Yes my receiver has the large/small speaker setting but it doesn't disable the subwoofer out when the speakers are set to large. When i was using it for HT i had the speakers set to large and the sub worked fine.
I think the sub out plug is only for digital sources decoded by the receiver (?)
I tried changing the setting to small and it didn't make any difference.
 
Are you trying to use something like "Direct", "Pure Direct", etc. mode? If so, that sort of thing often disables bass management.

Is the sub config set to LFE+main or something to that effect?
 
Tape out typically doesn't change the volume, as you have discovered. Does the sub not have speaker-level inputs? If not you could tap the speaker output yourself with a speaker to line-level converter gadget or a DIY solution.
 
Tape out typically doesn't change the volume, as you have discovered. Does the sub not have speaker-level inputs? If not you could tap the speaker output yourself with a speaker to line-level converter gadget or a DIY solution.

Yeah the sub has got speaker level inputs but only with spring connectors. In order to use them i would have to cut the banana plugs of the end of my not inexpensive speaker cables and buy another pair. It could be cheaper to get a new amp!
I will look into a speaker - line level converter, I didnt know they existed.
 
Yeah the sub has got speaker level inputs but only with spring connectors. In order to use them i would have to cut the banana plugs of the end of my not inexpensive speaker cables and buy another pair. It could be cheaper to get a new amp!
I will look into a speaker - line level converter, I didnt know they existed.

Just buy some very cheap speaker cables then?
 
Or get cheap banana plug sockets for your speaker wires to plug into, then run wires out of them and into the sub.
 
Last edited:
Many AVRs and processors will operate the sub just fine with analog sources, provided the configuration is correct. Knowing the specific model may help ascertain that.
 
The model is an AVR-1803. No pre outs, no processor loop unfortunately.
Its given me sterling service for over 10 years, I did some "back of an envelope" calculations and reckon its cost me about 4 cents an hour (not including electricity) over its life.
I'm not really into HT anymore so probably wont replace it but I have been thinking of a dedicated stereo amp.
I'd prefer not to use the speaker cable inputs on the sub due to positioning and WAF :no:.
i thought maybe i was missing something obvious with my amp but it looks like its a speaker to line level box or a new amp.
Anything to look out for good or bad with these speaker-line level devices?
Thanks for the input everybody :thmbsp:
 
I'm guessing you don't want to run your main speakers off the sub and your receiver doesn't have A and B outs for the speakers. How about connecting extra wires to the banana plugs in a Y fashion (if that's possible) at the outputs and running them to the sub?
 
I'm guessing you don't want to run your main speakers off the sub and your receiver doesn't have A and B outs for the speakers. How about connecting extra wires to the banana plugs in a Y fashion (if that's possible) at the outputs and running them to the sub?

Yep that's right.
I did wonder if it would be possible to run some extra wires from the speaker outs on the amp to the sub. That way I wouldn't have to have more wires running from the sub to the speakers.
Can I do that without frying my amp? If I hooked up two pairs of speakers to the one output it would overload it, will it be different because the sub is amplified?
 
The matrix of audio modes vs. speaker output in the owner's manual clearly indicates the subwoofer should play from analog sources in stereo mode using the normal connections to the speakers and the sub/LFE connection to the sub. There is no need to go in with workaround connection/wiring methods.

Is the intent to use just for stereo/2-ch with sub?

Have you reset to factory defaults and reconfigured, or just trying it with whatever settings are currently in it?
 
Yep, the impedance is so high your amp won't even notice. It's the same as connecting your speakers to the sub outs actually.
 
Back
Top Bottom