• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Wharfedale Owners Thread

Well still waiting as the delivery is taking a toll since covid BUT!
I just got a new amplifier. Was not expecting to be able to reach that level yet.
I just hooked up to my DM1400 my Accuphase E-203, which I got today.
And what can I say just WOW!
THE MUSIC IS ALIVE!!
Not only it looks good (to me at least) but it wakes up each notes.

Sexy piece of gear, there! I look forward to your opinion of the Linton.
 
This is my first post and also a kind of introduction.
Just a regular audio enthousiast, my aim is to get the best out of simple gear with just tweaking with cables, wires, placement en just common sense. My first speakers as a teenager were Wharfedale Dentons and I have used different models all my life.

I recently acquired a pair of Rosedales and just enlisted here to dig into all the info. While sounding great, I'm definitely planning on at least replacing the caps and recreate some decent fronts since these are warped and soaked in nicotine/smell like an army dumpstore. Drivers seem pristine in contrast to the quite neglected cabinets. At least, they outperform the brand new Denton 85th Anniversaries significantly on first hearing them.

IMG_20210421_120615 (2).jpg

A former project was the restoration of a set of Triton's which have the same mid- and treble units as the Rosedales but have 8"-woofers in a small but tall cabinet. I used them as pc-speakers and they sounded also excellent but after 10 to 15 minutes of listening my brain started to 'vibrate and buzz' which only slowly faded after quitting listening. After replacing the caps on the crossovers with fresh audio types, it had not more, but tighter bass and better overall balance and most noticeable more volume when comparing A&B. And no more brain-issues which was probably caused by some phase-shifting somewhere due to caps being out of tolerance and some were more than 50% off mark.

The caps of the Rosedales are of the same age and are probably just as bad so I guess things can only improve. Even more when they are a bit above ground level, any tips on stands?

I also heard the new Lintons and these are very, very good but I chose the Dentons for old times' sake and they are big enough for my living room. And better than anything I had before.
 
Hey can I play? I just acquired a lovely pair of Dovedale III - apparently a later version of them, going by the Rank Hifi badge on the back. Plans are a recap (probably film cap on the tweeter and decent electros for the rest), replace / upgrade the internal wiring and fit new quality binding posts. I'm also looking at re-finishing the cabinets to remove water rings. I'm pushing them with a NAD 7020i for the time being.

20210504_152135.jpg 20210504_152143.jpg 20210504_152202.jpg 20210504_153119.jpg
 
Hey can I play? I just acquired a lovely pair of Dovedale III
Come on down! The Dovedales look pretty good as is. Do these use the 1 inch purple dome tweeters? From what I know of these, they are very similar to the W60E model that was sold in the US. The backs look to have the same flaky material that they used on my Rosedales. You may want to seal the backs with several coats of something like thinned yellow glue to stop the flaking. Do these have any adjustments for mid or highs? One more suggestion, when you get the grill off, use a 1.5v battery to check the phase on the woofer. When you connect the battery positive to plus and negative to the minus terminal on the speaker the woofer cone should move outward. Rosedales were designed to run out of phase and I think they did it to permit some of the low mid range to cancel, making the overall response flatter - that's just a guess. Let us know how these sound when you get them re-capped.
 
Come on down! The Dovedales look pretty good as is. Do these use the 1 inch purple dome tweeters? From what I know of these, they are very similar to the W60E model that was sold in the US. The backs look to have the same flaky material that they used on my Rosedales. You may want to seal the backs with several coats of something like thinned yellow glue to stop the flaking. Do these have any adjustments for mid or highs? One more suggestion, when you get the grill off, use a 1.5v battery to check the phase on the woofer. When you connect the battery positive to plus and negative to the minus terminal on the speaker the woofer cone should move outward. Rosedales were designed to run out of phase and I think they did it to permit some of the low mid range to cancel, making the overall response flatter - that's just a guess. Let us know how these sound when you get them re-capped.

Yep 1 inch purple tweeter -

20210504_152256.jpg

No adjustments for high / mid anywhere on these. They have been babied from new by father / son owners so no need for battery clicking anything - the drivers are all good and the owners had never even had the backs off :-)
 
I checked the polarity of the woofers on the Rosedales: red wire = plus = positive = outward movement of the cone. Seems normal then...

The first of the two has been recapped and now being A-B ed. First impression is favourable since the untreated speaker is fading out again after a couple of days rest to let the old caps recover a bit.
 
I checked the polarity of the woofers on the Rosedales: red wire = plus = positive = outward movement of the cone. Seems normal then...

The first of the two has been recapped and now being A-B ed. First impression is favourable since the untreated speaker is fading out again after a couple of days rest to let the old caps recover a bit.
The phase for the Rosedale is dependent on which crossover you have. Usually models have adjustments for tweeter and mid run the woofer in-phase. I learned about the phase issue from other people in this thread that talked about it. What sucks is you can't run two sets of speakers if your woofer is out of phase because you'll cancel out the low frequency. My solution was to copy the crossover in the W70E (essentially the same set of speakers) and install the new crossovers.
 
It is probably a simple one, without adjustments. But a good one anyway. See pics before and after recap.

View attachment 2217262 View attachment 2217263
Looks like the same design I just removed from mine. Are you sure the woofer is wired in phase? The red wire going to my woofer was soldered to the negative terminal and the black wire went to the 4mH inductor. Judging from the way your crossover is wired, it looks to me like this is exactly how yours is set up as well. The red and black wires coming from the woofer are on the correct speaker terminals, that is to say red is connected to the positive terminal etc. So, if black is connected to your inductor, then your woofer is out of phase with respect to the mid and tweeter.
 
IMG20210430211751.jpg IMG20210430212024.jpg IMG20210430212832.jpg IMG20210430211507.jpg Got these Dovedale's a week ago..... they sound really nice.. very natural xx :angel::music::angel: Obviously they are Dovedale W2's..... but the label just says Dovedale ?? Seems a little unusual :beatnik:
 
These look just like early W60's 2-Way with port. Does that 5 inch have enough high end response?
W60's that would be a nice .... the highs are all there in fact I have rolled the pot back a couple of notches. The mid's seem slightly low, in a nice slightly scooped way. The label says RANK / Dovedale I've Googled but no exact match. I'm guessing they are around 1970 ish.....the main thing is I'm pretty sure they are original, and they (to my ears) sound great!!
 
W60's that would be a nice .... the highs are all there in fact I have rolled the pot back a couple of notches. The mid's seem slightly low, in a nice slightly scooped way. The label says RANK / Dovedale I've Googled but no exact match. I'm guessing they are around 1970 ish.....the main thing is I'm pretty sure they are original, and they (to my ears) sound great!!
Earlier, say 62-66. My guess would be 66. Wharfedale was still catering to the tube market at that time and the port makes these easier to drive. None of the design or printed material was spared by the fire at corporate HQ. Some people have pieced together somewhat complete specs for the E and D series speakers produced from the late 60's to early 70's but there were a lot of variations made by The Radio People in the far east who built these for their market. There are ways to date these. Do they have Alnico magnets(early 50-62)? Is the surround on the woofer fabric or rubber(some woofers had the ferrite magnet with cloth surround, early transition model)? Do they have oil filled caps? (very early). Forgot the most important thing, the date may be written on the woofer cone.
 
Last edited:
Earlier, say 62-66. My guess would be 66. Wharfedale was still catering to the tube market at that time and the port makes these easier to drive. None of the design or printed material was spared by the fire at corporate HQ. Some people have pieced together somewhat complete specs for the E and D series speakers produced from the late 60's to early 70's but there were a lot of variations made by The Radio People in the far east who built these for their market. There are ways to date these. Do they have Alnico magnets(early 50-62)? Is the surround on the woofer fabric or rubber(some woofers had the ferrite magnet with cloth surround, early transition model)? Do they have oil filled caps? (very early). Forgot the most important thing, the date may be written on the woofer cone.
Good call, I've checked the woofer for a date and there it is ...11/68. I got to say, given the part count and age of these beauties they really do sound sweet.
 

Attachments

  • IMG20210509102750.jpg
    IMG20210509102750.jpg
    118.3 KB · Views: 20
  • IMG20210509103936.jpg
    IMG20210509103936.jpg
    121.5 KB · Views: 20
  • IMG20210509100647.jpg
    IMG20210509100647.jpg
    135 KB · Views: 20
So I have a mint pair of the 70D's after buying a beat up pair to restore,with the pair needing restoration undergoing a full on restoration. I also added on 6" legs to the cabinets to raise them off the floor,and figured it would be much easier to do than build stands. The purple tweeters are shot and need to be rebuilt,so I need to find a place to do them. And a recapping is in order. These don't have the alnico mids or tweeters, so is it recommended to still do oil caps as I've read so far? Or would these be better off with other types of caps? I saw some used Morel MDT-29 tweeters ,and thought I read of others using Phillips. I did buy the Phillips ADO160-T8 and have been using these for now. L-Pads are shot and I have been rebuilding them as best as possible and seem to have them working now. Seems they are imaging the same. Wondering if I should just do the original veneer style or something a little more out there.

w70d1.jpg w70d2.jpg w70d3.jpg w70d4.jpg w70d5.jpg w70d6.jpg w70d7.jpg w701.jpg w702.jpg 20210411_160857 (2).jpg
 
The easiest way to deal with veneer is use a veneer patch to repair the damage. Since you have a larger area to fix, you could cut a straight line across and add a completely new strip. The trick to patching is being able to match. If you have a local store that sells veneer I would recommend taking a piece of the old stuff to match grain and color. Remember that veneer will darken when finish is applied so go a shade lighter than your sample.
 
Are you sure the woofer is wired in phase?

Regarding the Rosedales, almost finished, only the grilles left. No sand filled backs so I added some padding. Just in case...
Perhaps I screwed the original Rosedale finish (which lacks) but with black fronts like the W70E's it's just better and more in line with other speakers of that era.

With regard to the phase of the woofer, I ran a little experiment. I connected one Rosedale and one Denton (latest heritage series).
Surprisingly I didn't even have to balance or adjust anything, output levels are almost identical.
It sounds perfectly in phase and with my eyes closed sitting on the couch at the other end of the room I can't even say which speaker is which. Up close you can hear the Dentons being a bit more dynamic but the Rosedales have more highs and lows. Coloration is very nicely balanced however, even for their almost half-a-century age difference!

IMG_20210515_094444.jpg IMG_20210515_165736.jpg IMG_20210515_162357~2.jpg
 
Last edited:
Regarding the Rosedales, almost finished, only the grilles left. No sand filled backs so I added some padding. Just in case...
Perhaps I screwed the original Rosedale finish (which lacks) but with black fronts like the W70E's it's just better.

Regarding the phase of the woofer, I ran a little experiment. I connected one Rosedale and one Denton (latest heritage series).
Surprisingly I didn't even have to balance or adjust anything, output levels are almost identical.
It sounds perfectly in phase and with my eyes closed sitting on the couch at the other end of the room I can't even say which speaker is which. Up close you can here the Dentons being a bit more dynamic but the Rosedales have more highs and lows. Coloration is very nicely balanced however , even for their almost half-a-century age difference!

View attachment 2233317 View attachment 2233318 View attachment 2233319
The W70E's and Rosdales are among my favorite speakers. To me, they sound so open and symphonic. The other day I was playing the Broadway soundtrack to Camelot and it's like being 12 seats back from the pit orchestra. The same material on my KEFs would no way sound as good.
 
Back
Top Bottom