• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Yamaha RXV transformer problem

The PRD lead seems to loop through all the channels on the pre-amp board. I checked all the pre-amp leads where they connect to the main amp board & all six chans were around 3.7-3.8vdc as per the schematic. I also checked the bias for each channel..........spec says 100-300mV ..........all the mains were around 185mV while front effects were around 200mV.
So I'm left to wonder if that low voltage I was seeing for the PRD lead (pin 139 on u-com chip) is something I need to chase or...........where to next?
 
I also read a few times where some people had bad diodes on the CPU board causing erroneous DC PRT errors. Their solution was to replace them with 1N4148 so check them too on the DC detect line.
Check D503,4,5 most likely D505, these are probably smd.
 
Pin 139 PRD is limited to +1.2/-0.6V by D503,4,5. Expect 0.37V at connector
CB510 is too high for "dc offset". Source of PRD is preamp and PRD2 pin on
CB348(pg80) which is from the front L&R power amp outputs. You could try
lifting CB348 though it does have a B+ supply so probably nothing will work.
I'm leaning towards wanting PRD to be less than 100mV, so 370mV is too high.
 
Pin 139 PRD is limited to +1.2/-0.6V by D503,4,5. Expect 0.37V at connector
CB510 is too high for "dc offset". Source of PRD is preamp and PRD2 pin on
CB348(pg80) which is from the front L&R power amp outputs. You could try
lifting CB348 though it does have a B+ supply so probably nothing will work.
I'm leaning towards wanting PRD to be less than 100mV, so 370mV is too high.
I get .370vdc at PRD2 as well, which makes sense as they're ultimately connected.
I'm not understanding something. If the schematic lists "1.2vdc" on pin 139, isn't that what should be there? Either way the voltage is off, but I'm just trying to understand how this works.
 
I'm not understanding something. If the schematic lists "1.2vdc" on pin 139, isn't that what should be there?
Yamaha often give guiding values for fault situations, they rely on the tech to use his knowledge to sort out what's what.
PRD is for excessive dc voltage on spkr line, this voltage could be upto rails voltage if an output transistor failed c-e short.
Rails could be 40-50V which would "smoke" the u-com, so the diodes limit this voltage to something more acceptable to
the u-com.

I'd be looking at how to disconnect the PRD2 feed to pin 139 so try lifting CB348 but may need to be creative and lift a
resistor or jumper... Is PRD voltage caused by pre or power amps? You could try measuring voltages across R461,2,3,4,,
and R5,6(power amp), since PRD and PRD2 are connected they will be at about the same voltage however the source
of the problem will be a few mV higher than the rest. Need to find the resistor that has a higher/more +ve voltage on the
side that connects to the amp stage (apology a little unclear...)
 
OK......I lifted CB348 (ribbon) & the unit powers on w/o having to use protect mode. The speaker relays however don't close. I now see .465vdc @ lead for pin 139. Checking voltage on center chan amp board with CB348 lifted, PRD2 has about 18vdc, but I would think if that were the problem my reading @ p139 would've dropped, not risen.
R461-4 are impossible to reach without removing the pre-amp board from the unit, so i can't check those although I understand your logic there.

EDIT.......the 18v is on R5-6 which I see is tied to PRD2.......am I gettin in the ballpark? Problem maybe on the front effects chans?
 
Last edited:
I can't give you absolutes, troubleshooting these RX-V's is a real PITA.
Thinking 465mV on pin 139 with CB348 lifted points to a pre-amp issue and the
18Vdc on PRD2 is probably a byproduct of interrupting that +B2 supply to
the power amps. You could try isolating the PRD2 from the power amps by
lifting one end of J398 then reconnect CB348.

The fact you didn't need protect mode with CB348 lifted shoots down the above
theory.
upload_2021-2-11_13-4-19.png
 
OK, I'll give that a go after I clean up a mess I created. I started checking voltages earlier & noticed that, with CB348 lifted, I also was picking up -18-20vdc on the leads (FZR/FZL) for for the front effects chans while only getting about 30mV on the center chan. I realize now that one has nothing to do with the other since their B+ feeds are separate. In the process of trouble shooting, I blew the FZR OPT's. Not a big deal since I have many suitable replacements.
 
Back
Top Bottom