• The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html

biamp

  1. P

    BiAMp Marantz 5012 with Mcintosh

    I must admit that I love my Marantz AVR 5012 but I want to marry it to a Mcintosh Power Amp so I also get my beautiful blue meters. I know. I currently use the 5012 in BiAmp mode with my Klipsch Heresy IVs. It sounds great. Is there a way keep a BiAmp setup while using and external amp for the...
  2. Kalliman

    Yamaha A-460. To bi-wire or not bi-wire. That is the question.

    Hi, Very new to the scene and could use some advice. Picked up a Yamaha A460: https://www.hifiengine.com/manual_library/yamaha/a-460.shtml Pairing with Paradigm Monitor 7.v2's which can be bi-wired. I am assuming I can bi-wire speaker terminals and connect to A speakers L and R at amp...
    • Kalliman
    • Thread
    • a460 biamp biwire monitor 7 paradigm
    • Replies: 18
    • Forum: Solid State
  3. A

    Bi amping opinions

    I have been playing dabbling into separate lately and after playing with a few setups I finally found one I am enjoying but am wondering other than Y splitters if there is a way to Bi amp my speakers with the current set up i have. I have a Denon avr4308ci receiver as my preamp and a Nakamichi...
  4. topwik

    Mirage M595IS troubleshooting

    Hello and good day! I have a question about the Mirage m-595is. I just hooked these up as my bedroom speakers powered by an Onkyo TX 8160 stereo amp. I've noticed today that the rear tweeter might not be working. If I close-in my ear to the back of the speakers, I hear the woofer doing it's...
    • topwik
    • Thread
    • 595is biamp bipolar biwire m-595is m595is mirage troubleshooting tweeter
    • Replies: 14
    • Forum: Speakers
  5. David_NC

    ADS M12 Bi-Amp Conversion Success

    I've posted previously about converting my M12's to be bi-ampable. It seems that this is one of the few larger ADS towers that didn't have that option from the factory. My motivation for doing this is to be able to use a Dynaco ST-70 for the mids and highs and a 200 WPC Parasound SS amp for...
  6. J

    Bi-Amping the Rectilinear III 3.

    I have a pair of Highboys with the mid and high controls. I know I need to remove the woofer coil and the mid-range capacitor in order to bi-amp these. I want to confirm which cap and coil these are in the crossover. Also, I assume this is a 6db/octave slope but what is the crossover frequency...
    • jimghetto
    • Thread
    • bi amp biamp rectilinear rectilinear 3 rectilinear iii
    • Replies: 1
    • Forum: Speakers
  7. SmartPDX

    I am new to this site I am in Portland, Oregon need help with optimal set up of a music only sytem?

    Hello, I am in Portland, Oregon (east side area) zip 97086 I am new to this site. I am a not an audiophile. I am looking for advise on the optimal hook up of my components in a music only system. I am willing to pay (reasonable) for expert guidance. Looking for someone in Portland area for help...
  8. SmartPDX

    New to this site. Need help with optimal hook up of music only system components?

    Hello, I am new to this site. I am a not an audiophile. I am looking for advise on the optimal hook up of my components in a music only system. I am willing to pay (reasonable) for expert guidance. I have collected these components: B&K PT3 Preamp/Tuner B&K ST1400ii (series 2) I have two (2) of...
  9. MphisChris

    Splitting input source - nightmare

    Hi everbody! Sorry for the super long first post, but I am having problems splitting audio line level connections to seperate amps to power floor speakers and subs on my home stereo. Basically, I have a dj style stanton mixer/preamp and i am trying to split the signal to two different amps...
  10. M

    “Bi-amping” with one amp?

    Ok, this is not bi amping at all...though the sonic benefits may be similar. I have a Russound source/speaker selector lying around. So I tried setting it as follows: Preamp/amp to the input, tweets to one output, woofers to the other. Passive crossovers in my paradigm 11SE mk3 speakers...
    • Martin Angus
    • Thread
    • biamp paradigm russound
    • Replies: 7
    • Forum: DIY
  11. R

    Bi-amping question

    I've got some oak ridge acoustics speakers from 1990. They have two sets of terminals for each speaker. I'm wondering if I need to modify any of the connections between the woofer and the crossover before using the bi-amp feature. Here's some pictures: https://photos.app.goo.gl/gb8dIuJAHhDVfzm32...
    • roarke
    • Thread
    • biamp
    • Replies: 14
    • Forum: DIY
  12. G

    Marantz Biamp Question

    Hi all, This is my first post, but I have followed the forum for a bit. I own a Marantz SR6007 and a pair of B&W 603 S2s currently in a biamp setup. Overall, I am running a 5.2 setup. I have the marantz in biamp mode where the surround backs are powering the tweaters of the B&W 603s and the...
Back
Top Bottom