• The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html

bridge rectifier

  1. C

    Pioneer RT-707 Servo Board Troubles

    Hey all, I'm trying to get an RT-707 back into shape. It had been worked on before, caps that see the most usage have been replaced and the problematic small signal transistors that keep up the recording bias have been replaced with modern subs as well. It doesn't response to any speed...
    • CaseyWKC
    • Thread
    • bridge rectifier dc no control pioneer rt 707 servo assembly board speed issues swings
    • Replies: 7
    • Forum: Pioneer Audio
  2. JK-47

    Kenwood KR4140 Bridge Rectifier sub for S1B02-03 B

    I'm looking for a bridge rectifier sub for S1B02-03 B. Kenwood KR4140 Receiver. I can't seem to find anything online. Any help would be appreciated.
  3. mteetank

    Amp Size for Bridge Rectifier – Denon DRA-300 Receiver Upgrade

    Hi all, I am doing some restoring on my Denon DRA-300. The Denon uses two capacitors in its power circuit. One is 50V 6800uF and one is 5600uF. I have two 50V 12000 uF 20% left over from a previous project. The rectifier is a Shindengen S4VB 4 amp 200volt. Now for my question/ concern. I...
    • mteetank
    • Thread
    • bridge rectifier diode rectifier rectifier
    • Replies: 2
    • Forum: DIY
  4. ocdecio

    Marantz 4230 blowing fuse

    I got this 4230 and I found out the bridge rectifier was shorted, therefore fuses would immediately blow. I replaced it with a compatible bridge and turned it on with a DBT. The 100W light dimmed but not as much as it does with other receivers such as the 2225 and 2230. The dial lights came on...
  5. flatlinenj

    Marantz 4240, Back panel fuse blows when powered on.

    Problem: Marantz 4240, Back panel fuse blows when powered on. Troubleshooting: Test 1: Transformer: Disconnect input power leads on bridge rectifier 5B2. Power up unit. Measure voltage at transformer output: 42.0 Volts AC, Front panel lit. Conclusion: Transformer is good. Test 2: Power...
  6. B

    Phase LInear 300 sii bridge rectifier

    I replaced the bridge rectifier in my PL300 sii. I normally take a picture before doing something like this, but this time, I relied on my 72 year old brain to remember what goes where (BIG mistake). Could someone who has a working 300 post a pic of the bridge rectifier in circuit so I can...
  7. mrhandlin

    Hafler DH-500 - bridge rectifier? recommendations?

    Thanks in advance for your help. It's great to be part of a community of like-minded individuals. I've recently recapped an old Hafler DH-500. It's a bit unusual in that it has the pc10a version of the boards which don't quite match the manual available online. Anyhow, I've recapped it and...
    • mrhandlin
    • Thread
    • bridge rectifier dh-500 diodes fred type bridge rectifier hafler snubber
    • Replies: 11
    • Forum: Solid State
  8. tusntuk2

    Need help replacing KR-5600 bridge rectifier M4B-3

    Need help replacing KR-5600 bridge rectifier S5VB20. I used dlucy's suggestion of a 400v/35a bridge on a previous KA-3500 restore, but I found it larger than the original. Space is tighter in the 5600. Could I use something like a KBPC804PBF? It's 400v/8a (Vishay). I plan to use 10,000uf...
Back
Top Bottom