• The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html

resistance

  1. S

    Sansui AU-999 secondary transformer resistances

    Dear experts, I need help knowing the resistances of the secondaries of a 999 transformer. After having obtained :banana:a multivoltage (heavy) :) transformer for my AU-999 100 VAC version to replace the (missing) original one, I would like to compare the secondaries with a good working unit, if...
  2. Delta17

    Driver question, EPI M202 specifically

    Hello, I have read all the M202 posts I could find, and poked around other restore threads. I don't see an answer, or I am searching incorrectly. I have finally opened up my M202s to start restoring. I am hoping to just re-cap, clean the dial, and replace the binding posts. If the drivers are...
    • Delta17
    • Thread
    • drivers epi m202 ohms resistance speakers
    • Replies: 8
    • Forum: Speakers
  3. DordTrain

    Left Reel Lock-Up on my Sony TC-366

    I have a sony tc-366 reel to reel machine that I use occasionally to listen to music. Today, after doing so, the machine stopped spinning the reels. I took the cover off and discovered that everything worked fine, the right reel and motors all spun okay, but the left wheel was extremely locked...
    • DordTrain
    • Thread
    • issue reel to reel resistance sony sony tc 366
    • Replies: 4
    • Forum: Tape
  4. P

    JVC L-A55 tonearm resistance issue

    I've got a JVC L-A55 table in the shop right now, and this thing has me stumped. When I first began messing with this table there was so much resistance in the first quarter of the tonearm's arc, that it wouldn't move at all under normal operation. I've re-lubed the auto return mechanism...
    • Pioneerlyfe
    • Thread
    • automatic direct drive issue jvc l-a55 resistance skipping turntable
    • Replies: 5
    • Forum: DIY
  5. H

    KEF 107 restoration issues

    Hi everyone, I am currently in the process of restoring a pair of KEF 107s, complete with the original matching KUBE. They had a single previous owner who took good care of them, a retired sound engineer with a severely failing hearing—more on why that might be significant shortly. Talking to...
    • Huba Buba
    • Thread
    • burnt voice coil kef 107 recone recone kit resistance
    • Replies: 8
    • Forum: Speakers
  6. Red_Raider

    CR-2040 Phono Selector Switch?

    Just got my 2040 delivered to my door today. And I'm going over it very carefully. The faceplate needed a bit of cleaning along with a few pots. And the case may need a little attention from a furniture pen. But, overall I'm actually pretty impressed. It's actually in much nicer shape than I was...
    • Red_Raider
    • Thread
    • cr-2020 cr-2040 cr-820 phono selector resistance yamaha cr-2040
    • Replies: 12
    • Forum: Yamaha
  7. N

    New Cartridge Big Hum no Music

    I have an Bang & Olufsen RX TT and it had an MC 5 cartridge. It played vinyl but volume was soft but could be heard through the speakers. Sent cartridge off to be retipped to a nude MC 3. Installed and all I get is a hum which increases with volume. The ground is tight and the RX phono cables...
  8. Cheddar Bob

    Help with SX-1980 New AWR-154 Board pleeeeze

    Hi AK folks. Long time lurker, first time caller! I'm normally a vintage tube audio guy but couldn't resist a 30 buck SX-1980 at a garage sale maybe 15 years ago. It has the typical toasty power supply board with much of the foil hacked up by a PO. Back then, I couldn't find a used board to...
  9. Eric Lloyd

    Stupid DC resistance question

    While chasing a problem with a receiver, I decided to check resistance of my speakers and speaker wires. What I got was this: Realistic T-120: a) 4.2 ohms b) 4.3 ohms Infinity SM120: a) 3.5 ohms b) 3.6 ohms These are all three way speakers rated at 8 ohms, and I just put the meter across...
Back
Top Bottom