• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Troubleshooting CD Players

Dr. Audio,
First I'm sure I speak for many when I say 'Thanks!' for taking so much time to offer CD advice to all us less-enlightened CD owners who are trying to keep these things working. We last communicated regarding a Pioneer PD M730 that wasn't reading - the laser turned out bad, the tech said none to be found (which I expected) and he wouldn't install one for it anyway, because it would require soldering in - which, apparently, he's had trouble with... It ended up going to a recycler...
I'm looking at a Hitachi DA C70 12 disc unit that I got for modest cost - I discovered the laser didn't move, so a bit of lubrication freed it. It now plays, but starts to skip about 1/2 way through each disc - around songs 4-5, then will play the rest of the disc fine... Always skips, on each disc, about that spot... Lazy/fading Laser? Something else?
The rails seem well-lubricated, now... I can find replacement lasers (Hitachi HOP-M3), so may see about having it checked/replaced when they come in... Thanks for any advice, as always...
 
CD player only focuses and starts playing upside down !

Hello, I am starting repairing a nice Denon DCD-7.5 CD player with the Sony KSS-240A laser. 1991 vintage, cosmetically in great shape, unknown usage. Upon disk loading you can hear the laser hunting, but it does not apparently focus, and thus not spin. Picking up and turning the whole player physically upside down while loading a disk, carefully between the CD being held as part of the loading and the focus hunting, will get it running nicely !. Then, even turning the machine back the right way up, it plays great, till the disk is ejected (and thus presumably has to refocus next time). CD seems to be held secure, but with the disk out the spindle motor table seems to have vertical play of 1mm or so.

The KSS-240A to the left of the easy to see 3 pots has what looks like 6 vertical test points - can one of those be used for the RF eye signal instead of taking the drive out and soldering a wire to the RF test point ?. I could not find a layout/detailed schematic for the KSS-240A itself.

Have some CD experience though not seen this before, done some research, wondering if the fault is :
A) Worn bushing on the spindle motor ? thus the disk table is ~1mm too low (explaining why it can focus upside down ?), and I should raise the table carefully ? so like 2mm above the laser.
B) Maybe some spring ? that raises the laser assembly upon disk insertion has grown weak or sagging ? (so laser closer to the disk when turned upside down), and how do you adjust for that ?.
C) Sled rail ware ? (unlikely ?) - how fix/compensate ?.
D) Maybe the lens suspension has given up ? but the lens does bounce a bit when carefully pushed, and it's light weight, and rather not get a modern KSS-240A copy if the original, though 32 years old, is OK.
E) Or do I just go ahead and try increasing the laser current a bit ? (with the risk of burning out a good original lazer).
I have cleaned the lens & table, otherwise not taken apart yet. Sounds like a mechanical issue, thus would like to fix mechanically, appreciate ideas, thanks
I think the problem is mechanical. Don't mess with the adjustments. You would need to solder a test wire on the rf test point and ground.
Load a CD and turn off the power. See if the disc turns freely in the normal position. The loading belt may be bad and it isn't loading fully, or the suspension may have collapsed and the CD or the chuck is rubbing.
 
No, the pads are very delicate.
Well, took hours after mangling a couple of pads. I wanted to know just how painful the hard way is i guess. My flux pen enabled drag soldering and then wicking off - worked well. New chip is in...turn on...override the interlocks and....still the same old tricks. Wah!!!
(convinced myself it's dodgy caps - everything i've ever fixed has been caps pretty much)
 
Maybe if I ever decide to get back into my Fisher AD-923R, I will check out capacitors first. At least they are about 1000 times easier to deal with than the cotton-pickin' chips. Whoever thought of 100+ pin, surface-mount chips, anyway?

Doug
 
Dr Audio, the Opus is up for free takeaway (someone please..), but i did stumble across this paragraph from the Pioneer tuning fork series. Is replacing the RAM chip worth a try? I can only find a thru-hole version, not a SMT one so extra difficulty factor there.
One tiny improvement since replacing ic906 is that when spinning and attempting to read TOC, if i press the play/pause switch i get the relevant indicator light on the fl display. Tiny victory.IMG_20230704_150049_6_kindlephoto-156616769.jpg
 
Dr Audio, the Opus is up for free takeaway (someone please..), but i did stumble across this paragraph from the Pioneer tuning fork series. Is replacing the RAM chip worth a try? I can only find a thru-hole version, not a SMT one so extra difficulty factor there.
One tiny improvement since replacing ic906 is that when spinning and attempting to read TOC, if i press the play/pause switch i get the relevant indicator light on the fl display. Tiny victory.View attachment 2925265
I'm not sure that Pioneer uses the same system, but it sounds like that is only referring to slowing down the motor if the ram gets filled, not for constant control of the motor speed. It is possible that multiple ICs were damaged.
 
sounds like that is only referring to slowing down the motor if the ram gets filled
It sounds like a normal means of using the DAC clock as master to control the disc read speed; monitor FIFO buffer size to control the servo loop. Read mechanism is slave to the DAC.
 
It is possible that multiple ICs were damaged.
Yes, i'm thinking ic905 (the computer) and the RAM chip prob ok as they're only powered by the +5v line which never went down. The servo ic902 module is now my main bet - that does have a -5v rail to it which may have spiked. I can't buy the whole module, but I can get the cx20108 chip on there for a few pounds. Can i ask a basic question? On the schematic, looking at that module, it has all the voltages in red ink on all the pins. Is that voltage in the standby position?
 
Yes, i'm thinking ic905 (the computer) and the RAM chip prob ok as they're only powered by the +5v line which never went down. The servo ic902 module is now my main bet - that does have a -5v rail to it which may have spiked. I can't buy the whole module, but I can get the cx20108 chip on there for a few pounds. Can i ask a basic question? On the schematic, looking at that module, it has all the voltages in red ink on all the pins. Is that voltage in the standby position?
Somewhere on the schematic or manual they usually define the state for the voltages. it sounds like the unit took a powerline hit. Multiple semiconductors will be damaged. Some may fail later. I would not proceed with this repair. It's rare fore these ICs to fail, and if more than one fail it's always due to a powerline spike or ESD or lightening.
 
Sounds like the IC is bad. It's an inverter so with pin 5 low, pin 6 should be at 5V.
It is also possible that something is loading it down.
1. Try carefully de-soldering pin 6 and then see what the voltage is on pin 6.
2. If Pin 6 is still 2V, look at it with a scope to make sure it's a DC voltage and not a waveform.
3. If Pin 6 goes up to 5V when it's desoldered, Turn the unit off and measure the resistance from pin 6 pad to ground.
Hello @dr*audio sorry I am responding until now but I was traveling out of the country.
I desoldered pin 6 and measured voltage from ground to it and it gives me 5v. I measured resistance from pad of pin 6 to ground and it started at 4.17Mohms but it goes down a decimal point every second, at the time of the posting it was showing 2.90Mohms.
 
Sounds like the IC is bad. It's an inverter so with pin 5 low, pin 6 should be at 5V.
It is also possible that something is loading it down.
1. Try carefully de-soldering pin 6 and then see what the voltage is on pin 6.
2. If Pin 6 is still 2V, look at it with a scope to make sure it's a DC voltage and not a waveform.
3. If Pin 6 goes up to 5V when it's desoldered, Turn the unit off and measure the resistance from pin 6 pad to
The resistance keeps going down, at this point it shows 1.87Mohms
 
Last edited:
Lots of useful info here, thank you!

My Sony CDP-X111ES started misbehaving several months ago (skipping, failure to read discs) but the problem was intermittent. It failed hard about a week ago. Tray operation and drive / laser assembly vertical motion was OK. Lacking an oscilloscope I replaced the laser module (KSS-240A / BU-5BD1) using a cheap ($28) item from Liberty Electronics in the Miami, FL area. This appears to have solved the problem.

We'll see if operation continues moving forward.

Tim
 
I think the problem is mechanical. Don't mess with the adjustments. You would need to solder a test wire on the rf test point and ground.
Load a CD and turn off the power. See if the disc turns freely in the normal position. The loading belt may be bad and it isn't loading fully, or the suspension may have collapsed and the CD or the chuck is rubbing.
Many thanks to Dr*audio. I took my Denon DCD-7.5 CD player apart and the problem was the laser mechanism not fully lifting after loading, the noise I thought was focusing was actually the gears slipping. I lightly oiled the motors and spindles and dab of lithium grease on the sled bar, J track and lift cam, and now it works nicely - though really could do with a new belt after > 30 years.
I could not remove the loader front panel (any secrets ?) so had to disassemble more than necessary to remove the mechanism. My dislike of flexible connectors has increased as I did not re-insert perfectly squarely, shorting both the 5V and 7V supplies to GND. This blew a couple of the ICP-N15 fast fuses in the power supply. The Denon service manual is OK-ish, contains the operating instructions which is good, though some errors and no theory of operations. The unit now reliably loads and plays, great sound with 2 PCM-56P converters and quality 1990's build. My take-away is turning a unit upside down as soon as the disk is held during loading, is a trick to see if the belt and lubrication is marginal.
 
Many thanks to Dr*audio. I took my Denon DCD-7.5 CD player apart and the problem was the laser mechanism not fully lifting after loading, the noise I thought was focusing was actually the gears slipping. I lightly oiled the motors and spindles and dab of lithium grease on the sled bar, J track and lift cam, and now it works nicely - though really could do with a new belt after > 30 years.
I could not remove the loader front panel (any secrets ?) so had to disassemble more than necessary to remove the mechanism. My dislike of flexible connectors has increased as I did not re-insert perfectly squarely, shorting both the 5V and 7V supplies to GND. This blew a couple of the ICP-N15 fast fuses in the power supply. The Denon service manual is OK-ish, contains the operating instructions which is good, though some errors and no theory of operations. The unit now reliably loads and plays, great sound with 2 PCM-56P converters and quality 1990's build. My take-away is turning a unit upside down as soon as the disk is held during loading, is a trick to see if the belt and lubrication is marginal.
If you meant the cover on the front of the drawer, on most players there is a little catch on the bottom edge which you release by pulling outward slightly on the cover and then sliding the cover upwards.
 
Ok, I have an ultra rare one here: Luxman D-03 from 1984-85 (not to be confused with their presently available D-03X) made during their ownership stint by Alpine. A seriously stout and very good looking unit, much like the quality of the Denon DCD-1800 from about the same time frame. It is fitted with the Olympus TAOHS optical block which is so often maligned these days for it's declining reliability. Luckily this one is good and strong yet. Unit powers up, drawer opens and loads a disc just fine.

However, the spindle motor doesn't spin up on it's own, yet "assisting it" by hand, will quickly read TOC and begin playback, which it will do reliably with no dropouts or tracking errors all the way to the end of the disc (test disc being used has 13 tracks, 68:xx total run time).

Once stopped, it will not start spinning again without another manual assist, and if the hand spin isn't done pretty precisely, will error out and eject the disc quickly. I've very judiciously oiled the upper bearing on the spindle motor, with no change.

My question is this: should I more likely suspect the spindle motor, or the caps in the spindle motor drive circuit? Plan is to replace the latter anyway, but am wondering if @dr*audio thinks the motor is suspect, as that may bring this project to a standstill. Unfortunately, the motor is an ordinary DC brush type, and if it is shot, it may be difficult to source a replacement. I'm hoping the motor is good - and trying to decide how best to test it out of circuit - as once it is running, the player works beautifully. Or maybe it is something else entirely that I'm overlooking.

Note that I've been looking for a service manual for this model for months, to no avail thus far, so am flying by the seat of my pants on repairing it. Any suggestions and advice welcome.
 

Attachments

  • photostudio_1689811121131.png
    photostudio_1689811121131.png
    304.1 KB · Views: 9
Ok, I have an ultra rare one here: Luxman D-03 from 1984-85 (not to be confused with their presently available D-03X) made during their ownership stint by Alpine. A seriously stout and very good looking unit, much like the quality of the Denon DCD-1800 from about the same time frame. It is fitted with the Olympus TAOHS optical block which is so often maligned these days for it's declining reliability. Luckily this one is good and strong yet. Unit powers up, drawer opens and loads a disc just fine.

However, the spindle motor doesn't spin up on it's own, yet "assisting it" by hand, will quickly read TOC and begin playback, which it will do reliably with no dropouts or tracking errors all the way to the end of the disc (test disc being used has 13 tracks, 68:xx total run time).

Once stopped, it will not start spinning again without another manual assist, and if the hand spin isn't done pretty precisely, will error out and eject the disc quickly. I've very judiciously oiled the upper bearing on the spindle motor, with no change.

My question is this: should I more likely suspect the spindle motor, or the caps in the spindle motor drive circuit? Plan is to replace the latter anyway, but am wondering if @dr*audio thinks the motor is suspect, as that may bring this project to a standstill. Unfortunately, the motor is an ordinary DC brush type, and if it is shot, it may be difficult to source a replacement. I'm hoping the motor is good - and trying to decide how best to test it out of circuit - as once it is running, the player works beautifully. Or maybe it is something else entirely that I'm overlooking.

Note that I've been looking for a service manual for this model for months, to no avail thus far, so am flying by the seat of my pants on repairing it. Any suggestions and advice welcome.
Yes, the motor is shot. You can try spraying some Deoxit in any openings you see in the bottom of the motor, near where the wires connect or near the center of the bottom plate in the hope that it will get to the commutator. Failing that you can remove one of the screws that holds the motor in place and shoot some Deoxit in the hole. It may help to connect a battery to the motor and spin it up for awhile.
I have had zero luck finding replacement motors. If you do find one, you need to measure the height of the disc table from the bottom of the table to the mechanism plate, then make a gauge to that dimension so that when you install the new motor you can insert the gauge and push the table down until it hits the gauge. You can use white wood glue or Duco cement on the shaft before you put the table on, to secure it. Don't use Super Glue, you want to be able to remove the table at a later date.
 
@dr*audio, I appreciate that input. I'll pull the motor and see if I can resurrect it. I find it disappointing that after building such an exceptionally solid player in every other respect, Alpine/Luxman skimped and put this cheapo DC motor in for the spindle. Even Technics had spindle motors that were technically far superior and better designed than this. The bad news is there is no other (more) common player the D-03 was based upon to try and hunt down for parts, it appears to have been a 100% custom design by Lux. Interstingly, the D-405 of around the same time frame, one of which I also have here, is a reskin of a Toshiba XR-Z40, which makes finding a donor unit for at least some parts - cosmetics aside - a bit easier.

Aw well, I'll get to messing around with that over the weekend. Good advice on the placement of the disc table. I was aware of the need to be very precise in measuring the gap when pullling and reinstalling it, but it bears repeating again for anyone else reading this thread, in case they may he unaware of the criticality of that. Especially in a case like this, where optical block alignment instructions aren't readily available.
 
@dr*audio, I appreciate that input. I'll pull the motor and see if I can resurrect it. I find it disappointing that after building such an exceptionally solid player in every other respect, Alpine/Luxman skimped and put this cheapo DC motor in for the spindle. Even Technics had spindle motors that were technically far superior and better designed than this. The bad news is there is no other (more) common player the D-03 was based upon to try and hunt down for parts, it appears to have been a 100% custom design by Lux. Interstingly, the D-405 of around the same time frame, one of which I also have here, is a reskin of a Toshiba XR-Z40, which makes finding a donor unit for at least some parts - cosmetics aside - a bit easier.

Aw well, I'll get to messing around with that over the weekend. Good advice on the placement of the disc table. I was aware of the need to be very precise in measuring the gap when pullling and reinstalling it, but it bears repeating again for anyone else reading this thread, in case they may he unaware of the criticality of that. Especially in a case like this, where optical block alignment instructions aren't readily available.
Mabuchi made the better motors. The Matsushita motors are junk. I'll be curious to know which one you have.
 
Hello @dr*audio sorry I am responding until now but I was traveling out of the country.
I desoldered pin 6 and measured voltage from ground to it and it gives me 5v. I measured resistance from pad of pin 6 to ground and it started at 4.17Mohms but it goes down a decimal point every second, at the time of the posting it was showing 2.90Mohms.
Hello @dr*audio wondering if you saw my late response to yours regarding my issue, would you have an idea what can be driving the voltage at pin 6 down?
Thanks again for all your tips, and for sharing your knowledge with all here.

Regards,
Pedro
 
Hello @dr*audio wondering if you saw my late response to yours regarding my issue, would you have an idea what can be driving the voltage at pin 6 down?
Thanks again for all your tips, and for sharing your knowledge with all here.

Regards,
Pedro
It looks like the IC is bad, nothing is loading it down.
 
Back
Top Bottom