• The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html

maggie

  1. E

    magnavox tube amp 9403 input issue

    Hy my main system is just two channel , four way , and kinda vintage , pre amp dynaco pass 3 x -re stored with original boards and still with telefunken tubes , and lots of other upgrades around it , hours of hard work in the pre amp ----next the signal runs into a sony td-888 electronic...
  2. S

    MAGNAVOX 294H Help

    Hello, I just bought one of these in fairly good shape. I want to get her back to good working order. Below are some things that I have questions about if anyone can help. -How exactly do you get the turner chassis out? -Is there a schematic for the tuner circuit somewhere out there. I found...
  3. angelaudio

    Magnavox Magnasonic Console 128E amp & 129 preamp

    Hello fellow Akers hope you all find yourselves well. I just acquired this little console today and wanted to share some pictures and ask some questions. the thing is absolutely beautiful and well taken care of to boot. It has a Collaro changer on it which isn’t functioning right now for some...
  4. Barton Isaac

    Maggie 9304 Amp Threads?

    Hi Y'all, I figured instead of me asking a ton of questions, I'd ask if there are threads that y'all know of that you could direct me to. I've done a bunch of searches already without satisfaction. I'm looking to convert the Magnavox 9304 into an amp to power a CD player, Phone and MP3 via...
  5. Barton Isaac

    Power Section filter cap question

    The amps (guitar tube amps) that I've built have been single ended and 20 microF (uF) were generally the highest value I've used. I've just received an unmolested Mag 9304 and I'm going to remove the current Cap Can from the power circuit and re-cap. This amp has a 5u4 rectifier and the first...
  6. angelaudio

    Magnavox CR192 FM tuner help..

    Hello there folks, I just pulled this cr192 from an old and heavy chassis to give it a look over but I can’t seem to figure out how to make it work. The fish eye bulb lights up and so do the tubes so I’m hoping that it’s working but I can’t say for sure because the CR197 SW tuner that it came...
    • angelaudio
    • Thread
    • maggie magnavox console pull magnavox cr 192 magnavox cr 197
    • Replies: 1
    • Forum: Tuners
  7. Mikethenewb

    Maggie 185-23 Amp help

    think I made a huge mistake and if anyone can help me undo it I would be very appreciative. I removed the female molex plug for my magnavox 185-23 amp. I would like to be able to use the original controls but I threw away the plug and I don't know the schematics for the plug itself. If I can't...
  8. Brunt

    Magnepan 1.6QR repair question

    Hi everyone, I recently picked up a pair of Maggie 1.6QRs that were in dire need of some TLC. I'm currently in the process of regluing the wire loop ends back to the mylar but had a question for anyone that has had experience with Magnepans/their repair in the past. I found after opening up the...
    • Brunt
    • Thread
    • 1.6qr maggie magnepan magneplanar mellanox mgi project repair restoration
    • Replies: 8
    • Forum: DIY
  9. Tubeglowpio

    Dgse1 ultra linear

    Hey everyone, I've built a couple tube amps in the past but finally ended up pulling the trigger on building a dgse1 since I've heard mostly good things and love the sound of the maggie 8601 I suped up. I changed a few things from the schematic but mostly just the power supply to adjust the...
    • Tubeglowpio
    • Thread
    • dgse1 el84 maggie magnavox tube tube amp tube stereo ultra linear
    • Replies: 8
    • Forum: Tube Audio
  10. Amalgum

    resurect magnivox 142xx

    I came across a magnivox 142aa and a 142cc. Does someone know the basic steps to get these amps working outside their original consoles? There is an input connector to which the original console would have connected and through which switches and pots would have been connected. Does someone...
  11. C

    8802 tube swap 6EU7 to 12AX7 and grid voltage

    EDIT: [SOLVED] the problem was that I was counting pins backwards, i.e., I was reading the pin-out diagrams as though they were top views instead of bottom views. TL;DR: First project. Swapped 6eu7 for 12ax7 (with DIY adapter) but I'm getting 80VDC on the grid and don't know why. I'm...
  12. oldsmobuick

    Time to Replace Power Transformer in Magnavox 8802?

    My Magnavox 8802 has been fully recapped and new resistors all around. It sounds great but there is some tar leaking from the (original) PT, only a very small blob at the moment, and a vibration that is emanating from the transformer. The vibration is pretty noticeable in a quiet room. Should I...
    • oldsmobuick
    • Thread
    • 8802 maggie maggie console magnavox magnavox 8802 mods power transformer
    • Replies: 12
    • Forum: Tube Audio
  13. D

    Magnivox 9303 restoration help

    Hello, I am new to vintage tube amps. I do have some electronics experience. I've built guitars and done complete re-wiring of cars, etc. but I'm completely new to the amp restoration game. I recently aquired a Maggie 9303 amp. I found the original schematic and plan to make sure everything...
    • drewski13
    • Thread
    • 9300 series 9303 maggie magnivox mod modification restoration tube amp
    • Replies: 3
    • Forum: Tube Audio
  14. Giarcpnw

    Newbie looking for first tube project. Maggie 9308 or like suggestions?

    Hey all, Been living in the Solid State world for a while but was quite blown away at how good a friend's console pulled Maggie 9308 sounded. Now I'm wanting to try out the other side. Looking for suggestions on amps that are attainable semi cheaply and can be worked on. I like to tinker and...
    • Giarcpnw
    • Thread
    • 9302 9308 amp fisher maggie magnavox rca scott tube tube amp
    • Replies: 4
    • Forum: Tube Audio
Back
Top Bottom