• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Record Cleaning: Developing the Best Possible Methods

Status
Not open for further replies.
This energy used to argue valid, semi valid, and opinion based comments could be better served washing a few nice finds, ladies and gents.

Everyone, please, dial it down a notch. This isn't rugby, and I personally enjoy other perspectives than my own.
 
I just got my bottle of Triton and will be getting a Record Doctor V soon. I'm really looking forward to trying this solution out.
 
Here you go. This ought to fit your needs quite nicely. It is not Triton. It is Tergitol, but it is the other of the two formulas that Vince recommended: http://www.amazon.com/Professional-...=UTF8&qid=1463898467&sr=8-1&keywords=tergitol

3-5 drops of this per quart of water:

51tu9rQqFaL.jpg


Come back and tell us how you like it. I'm going to get some of this when my Mofi Super Record Wash runs out.

Enjoy,
Rich P
 
Last edited:
This is just an FYI post. My philosophy on home brew is to use as few ingredients as possible to accomplish the task at hand.

Thought I would check back in on this thread ... I've been using Nonionic Surfactant NP-6 (Tergitol) for a little over 6 months now. My current home brew.I make 8oz at a time.

31OQjU267rL.jpg


90% Aqafina (I use like other people use distilled water)
10% ... Swan Isopropyl Alcohol 99% pure
2 drops of NP6 (per 8oz bottle of home brew)

The results have been stellar to say the least ... best home brew I ever used ... Game Over as far as I'm concerned ... probably the last home brew recipe I'll ever use.

Only problem I had w/ NP6 is that it is so concentrated that it actually clogs an eye dropper (used to apply it) on second use. So I solved the problem by using a plastic cocktail stir stick to apply two drops of tergitol to 8oz ... I don't make a base solution like the OP. I dip the stick in NP6 bottle (NP6 clings to stick) and let two drops fall into 8oz bottle of water/ISO as above. Stir the solution w/ stick ... then throw away. I let the solution set for minimum of 24+ hours ... I have new bottle ready and waiting when I'm getting to the end of the first bottle.

Note: There are different types of Tergitol ... I'm only talking about the results I'm getting w/ NP6.
 
Last edited:
I've read the whole discussion from page 1, honestly, and am disappointed I'm late to this game.

I admired Vince for his clear explanation on the do's and don'ts for cleaning records, and also he base his decision on scientific reasons and not on opinions.

I've having problem with the solution, I cannot get it to fully cover the record as it keeps beading. I used a paint brush and also MOFI brush. I wonder is this normal?

As background info, I'd mixed Triton X-100 to distilled water to a 10% solution by first adding 5ml of Triton to 5ml of water. Then in steps of 5ml, 45ml of water was added making a final solution of 50ml. Left it over night to fully dissolve. Finally this was added to 5L of water so diluting the Triton to 0.5% mix.

What am I doing wrong?
 
Are you using any isopropyl alcohol in your solution? It should help to lower the surface tension of the mixture, and reduce the tendency to bead.
 
The first attempt I did, with 0.5ml Isopropyl and 0.5ml triton followed by 4ml of distilled water. I thought I did this wrong as it was beading and the Triton formed little pallets inside the bottle I mixed it in.
 
Dissolving the Triton can be a tedious process, due to its high viscosity. I find that adding it very slowly to room temperature water + IPA works pretty well. Constant stirring seems to be the key.

Perhaps the small volumes that you are working with are impeding your ability to provide adequate and constant stirring during the dissolution process.
 
You can go directly to the final batch concentrations without the Triton pre-mix, if desired.

Take 944 ml of room temperature DI water and add 65 ml of 99% IPA. Then slowly add 5 ml of the Triton slowly while stirring.

This should provide you with approximately 1L of 5% IPA/0.5% Triton record cleaning solution.
 
Last edited:
I usually mix just over 1 litre of cleaning solution at a time. I mix 3 ml of Triton into approx 85 ml of 99% IPA - this mixes up right away because triton is soluble in IPA. Then I add that mixture to 1 litre of Distilled water and it seems to mix evenly right away. Works very well for me. It is the IPA I believe that breaks the surface tension of the liquid. Vince explained to me that as long as you don't exceed 10% IPA you are fine. Some take that as %mass while other %volume - doesn't really matter IMHO as there are many variables....
 
I usually mix just over 1 litre of cleaning solution at a time. I mix 3 ml of Triton into approx 85 ml of 99% IPA - this mixes up right away because triton is soluble in IPA.

I didn't know you could mix Triton with straight Isopropyl without water. I'll try that.
 
I didn't know you could mix Triton with straight Isopropyl without water. I'll try that.

Remember... That's only just to get the triton to dissolve. You still need to use proper proportions and mix with the correct amount of distilled water before using it.
 
Still find the final solution beading up.

This is what I did. Made an initial solution of 10% Triton; 3ml Triton mixed with 3ml Isopropyl, followed by 24ml distilled water. The Triton looks dissolved and looks like a cloudy solution. Then used 1% of this and adding 99% water for the final solution. As it was still beading I finally went up to 5% / 95% solution.

I took two pictures one when applied the solution and another a few seconds later showing the beading effect.

1. Just applied.jpg

2. Beading.jpg
 
Last edited by a moderator:
Status
Not open for further replies.
Back
Top Bottom