• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Open Baffle Epiphany!

That OB setup you have with the RFT drivers are cool and I love that little amp! Do you just have them crossed over with a capacitor? Or is it active? Try mounting the tweeter so that it is firing up. I've done that with my latest set and it added the shimmer to the highs without the harshness.
 
That OB setup you have with the RFT drivers are cool and I love that little amp! Do you just have them crossed over with a capacitor? Or is it active? Try mounting the tweeter so that it is firing up. I've done that with my latest set and it added the shimmer to the highs without the harshness.

Would like to see how you mounted the upward firing tweeters. Got pictures?
 
That OB setup you have with the RFT drivers are cool and I love that little amp! Do you just have them crossed over with a capacitor? Or is it active? Try mounting the tweeter so that it is firing up. I've done that with my latest set and it added the shimmer to the highs without the harshness.
coil+capacitor, my friend, who is behind the amp and the Countryside electronix, made it for me. The full range RFT is not crossed, running tll 12500, the BEAG tweeter comes at 10000 Hz
I actually play this album, likes it very much:

 
Last edited:
That OB setup you have with the RFT drivers are cool and I love that little amp! Do you just have them crossed over with a capacitor? Or is it active? Try mounting the tweeter so that it is firing up. I've done that with my latest set and it added the shimmer to the highs without the harshness.

+1
 
You can try it on the floor behind the baffle or lower your mounting board so the tweeter is firing up and flush with the top of the baffle.
Either way should work fine.
 
Just simple have it mounted to the top of the baffle. It's pretty crude, but I've tried many different ways and this was my favorite. I found having them mounted this way allowed me to use a higher valued cap to get the highs that I needed and get rid of the beamy harsh sound when they were pointed at me.

Also, excuse the mess... we're rearranging and getting rid of a lot of stuff. :)

IMG_2518.JPG
IMG_2519.JPG
 
Just simple have it mounted to the top of the baffle. It's pretty crude, but I've tried many different ways and this was my favorite. I found having them mounted this way allowed me to use a higher valued cap to get the highs that I needed and get rid of the beamy harsh sound when they were pointed at me.

Also, excuse the mess... we're rearranging and getting rid of a lot of stuff. :)

View attachment 993435
View attachment 993436

Thanks. What value cap did you end up with?
 
I found having them mounted this way allowed me to use a higher valued cap to get the highs that I needed and get rid of the beamy harsh sound when they were pointed at me.
I ran this setup for a time. The top to the former console was at a 60 degree angle. The horn bounced the sound up and out.HornsMountedWired (1).JPG
 
Poultrygeist. I used a few different ones, but I'm pretty much settling on a 2uf with the tweets firing up as the sound is not glaring at me any more. adds plenty of sparkle. I like a prominent high freq. I imagine if I were to take measurements of the room it would look pretty bad, but my ears say different. :)
 
As I write this I'm listening to the Eminence ASD1001 ( forward firing ) tweeters with a 1.5 uF cap and so far I'm impressed. Since they fit the same opening as the Realistic tweets there's where I mounted them. And they look like they belong there. I had a bit more air with the open backed Realistics but also some sibilance especially with Diana Krall SACD's. No sibilance with the ASD1001's. I want to spend more time listening to them to make sure there's no fatigue which can happen with compression horn tweets.
 
I found that the the ASD1001s were pretty clear and not really harsh. However some voices that tend to sound a bit raspy or "harsh" (not that they are bad singers, just their style) are played back with the sibilance glaring at you. My guess is they are very revealing of the source and it goes to show you how big of a factor system synergy is...
 
Since y'all are talking about tweetage/supertweetage, I'll drop this and run.
Using these with my Frankenaltecs now as supertweeters (1 uF first order XO, padded). They are very nice (and none too expensive, either).
Very sensitive, too.

https://www.parts-express.com/bc-de35-neodymium-mylar-bullet-tweeter--294-580

They may be OOP and may be a little difficult to find, unfortunately.

bc-de35-size184.gif
bc-de35-back-size184.gif


source: http://www.usspeaker.com/B&C-DE35-1.htm
 
Talk to me about Mark Audio drivers? I've seen a few instances of people using these in open baffles and am intrigued. They appear to have a decent response chart, and cover a lot more of the frequency range than other drivers do...

I'm thinking about pulling the trigger on them, but not sure if I should do that or save up for some of the big Altecs.

PS. Sorry to double post.
 
Just looked those up. They look interesting. Very sensitive at 108db! Do they run too hot with your other drivers?
They're padded down. They are not harsh. They may even be a tad (no pun intended!) better than the Fostex T90As I've been using -- at least for my aging ears -- and at a fraction of the price. They're the real deal.
 
Back
Top Bottom