• Check out the Annual AK Secret Santa exchange Program, signup before November 23rd in the AK Charities & Christmas forum!

Open Baffle Epiphany!

Joe,

I agree with assessment. The Tang Bands are some of the best looking FR drivers around but they never engaged me like the Zeniths and Lowthers. A little too polite and laid back but still a good driver that many folks might enjoy. I sold mine to a friend when I got a deal on some slightly used Lowthers.

P2060001.jpg
 
The Tang Band 1808's have all the goodies including heavy cast frames, powerful neodymium magnets, copper phase plugs and exotic fiber cones. My friend who bought mine thinks they hung the moon.

P9160017.jpg
 
Compared to the Tang Bands the Lowthers are an entirely different animal. Unlike the polite TB's the Lowthers have that jump factor with an incredible amount of detail. Some might not like all that hyper detail but they're great if you want to hear the spit in Mile's trumpet which I do. As a winter project I hope to build MJK's MLTL cabinets to see how the Lowthers perform in that configuration. Love them in OB but I'm curious and always looking for a new project. Not an inexpensive project by my cheap standards as the parts alone for the baffle step circuit run well over a $100.

PA020003.jpg
 

Attachments

  • PA020003.jpg
    PA020003.jpg
    97.4 KB · Views: 6
Accidental Open Baffle.

I just ordered a pair of 10" full range field coil drivers. I am going to build nice cabinets for them but I can't get to them until February. So, I decided to stick them on open baffles so I can use them and break them in until I can build the cabs.

Measurements to follow.
 
Compared to the Tang Bands the Lowthers are an entirely different animal. Unlike the polite TB's the Lowthers have that jump factor with an incredible amount of detail. Some might not like all that hyper detail but they're great if you want to hear the spit in Mile's trumpet which I do.
:thumbsup:Sounds like my kind of speaker (if it was affordable to me at this time).
I'm not a fan of polite laid back etc... I know what real music sounds like and that's the way I want to hear it.
I don't listen to orchestras through earplugs so why should I want to hear my speakers that way?
 
Isn't the baffle step correction circuit correcting for the effects of the baffle, not the driver? And don't OBs have baffles?

You have to take both into consideration. Some single drivers work in certain enclosures without need for correction while others don't.
 
Last edited:
Accidental Open Baffle.

I just ordered a pair of 10" full range field coil drivers. I am going to build nice cabinets for them but I can't get to them until February. So, I decided to stick them on open baffles so I can use them and break them in until I can build the cabs.

Measurements to follow.

Who knows they might sound so good in OB's that you won't have to build cabinets. :)
 
Or MiniDSP, which is only $100 and can be used in tons of configs...

My experience is that anything added to the signal path can add it's own sonic signature and that's especially true when using a highly resolving SET amp. I can hear my active crossovers in the HF but not in the less critical LF. The MiniDSP is one of the most affordable and versatile actives except for the fact that it requires a PC and doesn't allow adjustments on the fly.
 
Compared to the Tang Bands the Lowthers are an entirely different animal. Unlike the polite TB's the Lowthers have that jump factor with an incredible amount of detail. Some might not like all that hyper detail but they're great if you want to hear the spit in Mile's trumpet which I do. As a winter project I hope to build MJK's MLTL cabinets to see how the Lowthers perform in that configuration. Love them in OB but I'm curious and always looking for a new project. Not an inexpensive project by my cheap standards as the parts alone for the baffle step circuit run well over a $100.

View attachment 1679137

I will be selling off shortly. I really like the TB but yes to polite (great descriptor) Can I take it the pic is your lowther setting over twin Emm. Alpha 15's ? if so do you have a pic from the rear ? if not can you tell me do you have 1/2 an H-Frame on the rear to improve bass ? where do you bring the bass in freq wise ? & how are the twins wired parallel or series ? Lot of questions I know but I am planning something similar except I want to build a thick baffle mount drivers from the rear and have a small flare similar to a mini horn im thinking 3 inches thick 4 pieces of 3/4 MDF

My lowther pm4a are close to 30 pounds each and need a strong baffle to support that huge alnico mag. I put them on a temp baffle and was happy with the sound but nervous about the weight
 
My experience is that anything added to the signal path can add it's own sonic signature and that's especially true when using a highly resolving SET amp. I can hear my active crossovers in the HF but not in the less critical LF. The MiniDSP is one of the most affordable and versatile actives except for the fact that it requires a PC and doesn't allow adjustments on the fly.
I used an old laptop and adjusted it on the fly that way... so yes, it needs a computer, but it literally takes me a few minutes to set a laptop on a chair by my system and swap the USB cord from the powerstrip to the computer, connect, alter parameters, and apply them.
 
My lowther pm4a are close to 30 pounds each and need a strong baffle to support that huge alnico mag. I put them on a temp baffle and was happy with the sound but nervous about the weight

Here is an idea courtesy of Mr Content from down under:

cUYl3xPm.gif


bcFML65m.gif


rEd6Qj3m.jpg
 
I will be selling off shortly. I really like the TB but yes to polite (great descriptor) Can I take it the pic is your lowther setting over twin Emm. Alpha 15's ? if so do you have a pic from the rear ? if not can you tell me do you have 1/2 an H-Frame on the rear to improve bass ? where do you bring the bass in freq wise ? & how are the twins wired parallel or series ? Lot of questions I know but I am planning something similar except I want to build a thick baffle mount drivers from the rear and have a small flare similar to a mini horn im thinking 3 inches thick 4 pieces of 3/4 MDF

My lowther pm4a are close to 30 pounds each and need a strong baffle to support that huge alnico mag. I put them on a temp baffle and was happy with the sound but nervous about the weight


In this picture the Alphas are wired in parallel and powered by two Dayton amps that have built in crossovers. I don't recall the crossover setting but the Lowthers run full range powered by a 2a3 SET amp. OB bass is really special.

PA020005.jpg
 
In this picture the Alphas are wired in parallel and powered by two Dayton amps that have built in crossovers. I don't recall the crossover setting but the Lowthers run full range powered by a 2a3 SET amp. OB bass is really special.

View attachment 1680793

So you are of the opinion that full OB bass is superior to H-Frame ? can you articulate why ? Im currently using a single goldwood 18 H-Frame per side powered by a crown xls1002 (More power than is required) I keep jumping around with the crossover point trying to find that sweet spot. It bugs me when the overlap between the FR and the bass is evident. I started at 150 dropped to 100 and am now at 170hz I was using a Marchand xm9 but decided to try and run the FR at FR. The Zenith sound pretty good, the Jordans sound amazing but are to power hungry my Decware SE84 are only 2 wpc and with Vinyl the Jordans become an issue. Gets a bit maddening trying to decide on a driver & crossover point.

Here is an idea courtesy of Mr Content from down under:

cUYl3xPm.gif


bcFML65m.gif


rEd6Qj3m.jpg

Looks like a possible alternative thanks
 
Joe,

You can read what Linkwitz concludes about OB's and OB bass here.

https://www.linkwitzlab.com/conclusions.htm

Yes I have read many of Linkwitz theory, observations Genius, gone to soon. I looked it over again Thanks
Rainy here been playing all day. Decided to try my home made sealed 12" subs in the mix Lets just get crazy. FR at Full signal from the decware, 18 goldwood running 60 up to 170 HZ subs picking up everything below 60hz actually cleaned up the bass on some bass heavy material. The 18's are great but can get distorted when drawn on low at volume

You can learn a good bit on a day like today, I never knew sealed was so important on a sealed sub I was lazy when I put the subs back together and left out 4 of the screws on each those small holes were chuffing an amazing amount of air and it sounded like something was vibrating in the room. Down on the knees looking all over for the vibrations, wife noticed it at the subs I thought no way till I felt that air
 
Back
Top Bottom