• The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html

connectors

  1. michaelm101

    Corrosion Prevention on Outdoor Connectors

    I just installed new banana plugs and had to chop over an inch of wire to get away from the corrosion. A few more times like this and I'll run out of length on these long runs of cable that are inside wall and neatly stapled through the patio area. What's the ticket for weatherproofing these...
  2. A

    Is my Technics tonearm 4 pins connectors damaged ?

    Hello, I’m new to the forum that i’m reading all the time to get some informations ! I’ve a question about an Technics SL-1200MK7 that i’m not using for DJing. Do removing headshell daily to clean my stylus can damage the 4 pins connector inside the tonearm ? I’m using the stock Technics...
    • Arthur92
    • Thread
    • connectors damaged headshell technics turntable
    • Replies: 2
    • Forum: Turntables
  3. gdmoore28

    Any Idea How These Are Used?

    I've never seen this spade terminal arrangement before. Seller says that "each pair of terminals is insulated from the next." Anybody have any idea how these are used? Applications? They were found mixed in with barrier-type terminal strips such as used in older speaker connections. GeeDeeEmm
    • gdmoore28
    • Thread
    • barrier strips connectors spade lugs terminals
    • Replies: 8
    • Forum: DIY
  4. Pentotark

    Old type binding posts, which connector?

    On the back of my Marantz Imperial 6 there are this old type of screw binding posts. Right now the bare cable is wrapping around them as you can see in the picture I attached to this post. I would like to make an easier way to plug and unplug the cables without changing the binding post type...
  5. bar72

    Connecting Turntable to Tascam US122 mk2

    Anyone help out with how I would connect turntable rca leads to the Tascam US122 mk ii usb soundcard line in? unsure what jacks the line in uses? thanks
    • bar72
    • Thread
    • connectors jacks tascam turntable
    • Replies: 6
    • Forum: Turntables
  6. S

    B&W DM11 speaker connections

    So I just bought a pair of B&W DM 11's as part of a lot of electronics. I went to hook them up and there are just a pair of metal holes in the back. As in holes and no spring clips, binding posts or other obvious means of securing speaker wire I can see. The holes aren't tapped so it doesn't...
    • special_20
    • Thread
    • b&w connectors dm11 mystery speakers
    • Replies: 3
    • Forum: Speakers
  7. marini

    Wire-to-PCB connector. Which one?

    Hi all, I've been struggling with the task of "wrapping" a wire around a pin (jumper) on the PCB. You know, when you decide to replace a small bulb (lamp). It never gets firm enough, so it can become loose and bad things can happen inside the equipment. I thought about using some sort of end...
    • marini
    • Thread
    • bulbs connectors lamps wire/cable
    • Replies: 11
    • Forum: DIY
  8. L

    Turntable problem with PIONEER LX 424

    I have bought Pioneer reciver LX 424 ( I think it is the european version of SX 424 ). It is near mint condition, and it sounds perfectly on radio broadcast The "problem" shows when I start the gramophone. It sounds blury and vocal is kind of distant ( like you are hearing it from some hall )...
    • llorca
    • Thread
    • connectors lx 424 pioneer troubleshoting turntable
    • Replies: 5
    • Forum: Pioneer Audio
Back
Top Bottom