Hi all audio experts and lovers,
I am currently building my "forever system" (or at least a very long-term one) and would love a sanity check from the experienced ears here before I pull the trigger. I'll add as much details for you to help :)
I am based in Amsterdam (which means wooden...
Are there any Accuphase owners who can share (if applicable) their experience with the P-300 line of power amps? Any big sonic differences between the original P-300, the P-300V and the ones in between?
Hello Everyone!
I am new to this forum but everything I have read leads me to believe I am finally in the right place for gaining some knowledge on my old Accuphase amplifier.
So right off the bat, here's my basic setup. Accuphase amp driving 200w Pioneer HPM 100's. I have a Technics cassette...
Hi Accuphase experts, I’ve noticed on my Accuphase C-200 the chassis has a tingle when you touch it while its on, its a two prong plug version, any suggestions what could be causing this and where I can look to track down the fault? I see someone has replaced the IEC socket at some point and...
Hi everyone!
I completely recapped the Accuphase P-266. Once the amplifier is on, it runs great! But charging 4x 22,000uF filter capacitors causes a high inrush current.
Every time I first start it, the circuit breaker is trips because the inrush current is too high. This also happened before...
Hi everyone!
I have changed all of the capacitors in this power amplifier, including the filter capacitors, as the old Elna's were very swollen. In addition, I've replaced all relays as well. I am very happy with the results! Now, I need to adjust the bias in the "Normal mode" (class AB) and...
Dear Accuphase lovers,
I was searching for it forever and then all of a sudden *poof* it was uploaded in high quality to Hifi Engine :banana:
Complete service manual + schematic and adjustment info.
Please beware that it is for units starting with serial number F4Y001
I tried to upload it...
I’d like to offer my impressions of the driver boards offered here:
https://audiokarma.org/forums/index.php?threads/new-driver-boards-for-accuphase-e-202-and-p-250.978124/
I picked up an Accuphase P250 a few years ago and it has now found its place as the primary amplifier used in my main...
I started working on an Accuphase e-202 for a friend, they weren't sure what was wrong with it as it had been sitting for almost a year since it stopped working.
I was going to power it up on a dim bulb to see what was wrong with it, but opened up the amp first to see if anything was visibly...
Hi all, I have just purchased an Accuphase E-205 which apparently has a channel with the output transistors having problems.
The other channel seems to have been fixed previously.
I would like to know if someone could help me to make it functional.
1. Help me know if the modified channel could...
The only SM I have available shows the standard driver circuit for PCB 710-0002-00, however I'm seeing a fairly major modification that appears to be factory but I may be wrong. I've read the service supplements and aware that in April 1976 it was recommended to remove D6 and R35 and replace...
Hi all, it has been quite a while since I have posted on Audiokarma - hoping I would be able to tap into your collective Accuphase expertise. I've acquired a early 2000s Accuphase E-212 which sounds great, but was in a bit of a sorry state when I purchased it (quite dusty inside and out). I have...
Greetings!
I've had this Accuphase C-200 Preamp for several years now. Since getting it, it has exhibited some distortion in both channels after it warms up for a few minutes and only with low volume levels. If I give the signal more gain (volume) the distortion seems to disappear. The signal...
Hello all,
McIntosh C20 vs Luxman CL34
I currently have Monitor Audio GX200 (2 x 5.5" bass driver; 1 x 4" mid-range driver; 1 x ribbon transducer) and an Accuphase P300 amp with Primaluna Dialogue Premium Preamp. I'm looking for a different preamp as the PrimaLuna isn't doing it for me...
hi All ,
I am currently in the hunt for a new amp and been thinking of getting either one of these two vintage integrated amp but having a hard time choosing since both got pretty stellar reviews.
I got pretty reasonable deal for either ,but unfortunately since its vintage gear online , its a...
Hi,
I’m based in Moscow, Russia, and t’s my first post here - hopefully I’m not messing it up as to where to post a query such as this.
I’ve been out of the hi-fi mania for a good few years and now am trying to catch up as I’d like to upgrade my early 2000s setup to vintage.
I have a...
Hello All,
I have been lurking this forum for a couple weeks devouring all info on the P300 and reading many excellent posts. I have learnt a lot but am still a novice. It is time for my question:
I have an Accuphase P300 that has been pulled out of 20 year retirement. I've been playing it for...
Hello everyone!
I would like to restore my dad’s 1979 Accuphase P260. The amplifier has had a rather hard life. As of today, it is not fully functional.
The amplifier’s history:
It was bought in the 80’s as fully functional.
In the 90s, the amplifier got water damaged; it was repaired: the...
Hi all,
I recently had the chance to listen to an Accuphase pre / power combo (C200L / P300)
and really liked it.
It had a very non-intrusive sound, but at the same time managed to present a good amount of detail.
Can any Accuphase fans out there throw some suggestions my way?
Would prefer an...
Does anyone have schematic info on this model? I have dc offset causing the relay not to energize and the amp will not come out of protection. I can’t seem to adjust this. Any help would be appreciated
Thanks
Hello,
I am here with an Accuphase E203 integrated amplifier and I am missing the adjustment set up for the amplifier part.
I am talking about the following pots: VR1, VR2, VR3 and VR4.
Thank you for the help
Alain
Hello dear members,
First of all, I want to apologize for my English
I live in France and I restore vintage HIFI for many years (for my own)
(Here are some Youtube links )
YouTube
YouTube
YouTube
YouTube
I had the opportunity to buy recently in Japan an Accuphase P-300S
I have already restored...