Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
The move to the new server is done. There are some software and database maintenance updates in process. This has us passing the hat around to help out. We appreciate any donations. Seriously, even a dollar helps. The payment page may be found here - https://www.audiokarma.org/support.html
Hi everyone I'm new here. I got this Marantz 2230B and wonder if this can be repaired. It sounds good but after a while the left channel drops. I tried switching the speakers to see if it would be the speaker. I cleaned the contacts and the potentiometer. Then, I tried switching the amplifier to...
So I just bought a Luxman r 1050 receiver and have been working on it for a couple of hours now. I have it to the point where it's basically fully functional however there is a bit of a weird issue that I am not too sure about. The volume indicator leds only work if the dolby fm feature is...
Hello all, some time ago I aquired two Sony PS-X800 turntables, both are faulty, and I would like to share with you the entire job of fixing and calibrating.
First one I'm tryng to restore arrived to me from Rome, I bought it completely dead, in acceptable cosmetic conditions but without cover...
Hey guys first post/thread here, need some help.
Recently purchased this Yamaha Natural Sound Stereo Amplifier A-7, which as far as I can tell is a Japanese Domestic Market model of the A-960 which means it runs on 100V. I live in a 230V country, so I used a step down transformer rated at 110V...
Greetings,
A very close friend from high school convinced me to go the Hafler route many years back and I purchased both a DH-110 preamps and XL-280 (both in kit form) just about 35 years back. Though I've had a few minor connectivity issues arise over the past few years with the DH-110, the...
Hi! The two pushbutton switches on my Hitachi HMA-8500 mkII broke while back (meter range &BTL). It is now at an older Hifi enthusiasts house for repairs and we have sourced a good replacement for the 12-pin meter switch but we are in search of a 24-pin pushbutton switch that will fit. It needs...
Hey there,
I recently acquired an Onkyo TA-R22 stereo tape deck at an estate sale. It seemed to be in working condition -- however when I plugged it in and gave it a listen, there was a pretty enormous audio quality issue. I figured it was likely the heads and pinch rollers that needed...
Hi,
Today I went to a local electronic parts shop where I buy lots of "run of the mill transistor and other brand new "e-waist" :)
The owner had a bit of spare time And he told he might have a nice stack of ORIGINAL **N.O.S** STK Power AMP modules Might be coming up for sale. There are some...
hola a todos, tengo un amplificador antiguo marca Sony modelo TA-F3A, el problema es que no funciona, resistencias quemadas fusibles quemados y transistores no los he comprobado todavía, según he leído estos amplificadores tienen problemas con 2 diodos en concretos pero no se cuales son sus...
Speakers: Bang & Olufsen Type M Passive Loudspeakers
Reciever: Sansui QRX-4500
Turntable: Project Debut Carbon
Hey all, recently I’ve noticed that after turning off my reciever, my left speaker makes a consistent/replicable noise after 10 seconds or so. It only lasts a few seconds, but it’s...
See title. I was looking around online and read a thread where someone fixed the issue by recapping the power supply. I am pretty sure this is necessary regardless considering the lights sometimes dim a bit out of nowhere. But is there anyway to make sure that this is indeed the issue?
So I bought what I thought was a luxman sq 507x but what ended up being a luxman sq505x with a 506 front secondhand a couple days ago but it has a dead right channel. After some trouble shooting I found out that someone had connected the pre amp connector switch incorrectly so I was hoping that...
Hi,
I have a Roksan Kandy integrated amplifier, with multiple working inputs. But the "CD" input has no sound.
I can repair electronics, but I'm confused with this. The RCA connector itself is fine, it passes current with a multimeter. It then goes into a circuit, circled in red:
Is it...
I just bought a broken at33ev cartridge from which two of the connector pins broke off/fell out. See the picture I attached. I was wondering if there was a way to get this repaired and what the average price of something like that would be. And if it's possible to even repair this. The...
I got a mitsubishi lt5-v today that does everything except move the tonearm left or right. I checked the sensors but both the leds and the resistors are working as they should. I checked if the motor was running and it worked just fine. If I move the arm by hand it drops down at the correct...
Alright, so I've got a Marantz 4270 with a bad channel, spitting out DC and throwing it into protection mode. Only one of the output transistors was shot, I believe it was the one that handles the negative swing. Otherwise, all the semiconductors on the board and otherwise are testing OK.
I can...
I finally got this thing going last night... tons of work and it's a complicated little beast!! But while I had this circuit working for a short time, I swapped out a transistor and now I have some SLOW motorboating going on... that gets faster if I adjust certain parameters. I'm realizing there...
I’m having an issue with a volume pot where where it only works when I hold the knob at a specific angle. When I let go of the knob the left channel plays at a random volume , and the right channel plays at where ever the knob is set. When I jiggle the knob and hold it both channels sync up in...
For reference the record player is a yamaha yp d4
I have this record player that works but has a few issues. The two main ones being that it spins at the correct speeds but it slowly speeds up over time. And also that unless I turn the internal potentio meter all the way up for 33 rpm it just...
Hello
I've been offered one of three FM generators at a very reasonable price. I intend to use it for AM and FM alignments. I don't have a distortion analyzer, so I probably won't be doing MPX alignments, so while I appreciate that one of the two units has stereo, and one does not, I likely...
OK so I'm sure there are a lot of Advent rebuilds on this site but I figured its easier to start a fresh thread. I am new at this repair scene and was hoping folks could help me on my way as I make silly mistakes. I did review a handful of existing threads ahead of time so I had a starting...
I have this yamaha tc 720 and apart from all the belts having turned to mush it has a weird issue. I can't really describe it so I made a video.
It seems it loses and quickly regains power every second or so. Is this due to the belts not being there or is something else going on?
I have a yp-d4 that I have been working on for a while. I recapped it and cleaned all the pots but the turntable still isn't working correctly. I removed some of the pots out of the circuit and after this it worked fine at 33,3. I also got it to work a few times before after intense cleaning of...
Professor Bizzt used to sell a dustcover hinge pocket strengthening kit for the Sony PS-X800 & PS-X555ES turntables. When I did a search I see where he has sold the kits, but the images are not available. When you go directly to his webstore.com site, they are not listed as being for sale at...