Found this pair of Spectrum Audio speakers in a thrift store (Sweden) with an intriguing coaxial build. There is no model identification except the Spectrum Audio logo on the grills, they seem to be a larger version of Spectrum Audio 108CD (as seen here Spectrum Loudspeakers-108CD -...
It’s no secret that the cabinet on the MCS-3233 left a lot to be desired when compared to what Pioneer and Marantz jacketed many of it’s receivers with. Classic Receivers website wrote, in referring to the cabinet, “it was a weak point of the receiver. It was fairly cheap quality and tends to...
Howdy folks... it's been a while!
For various and sundry reasons, I have a lot of unfinished projects, and I'm trying to make a concerted effort to ... finish some of them! I know, right??
Nothing terribly serious, mind you... just life + the usual shiny-object-distractions that are...
Hello!
I have started, and am close to completing, a restoration of some XPL 140’s, but I’m in need of some assistance regarding the baffle material and rejuvenation.
I’ve bought new neoprene foam to replace the damaged original. I did extensive research to get the right type. Underneath where...
Hi all,
Long-time lurker, first-time poster. I recently found a Fisher 400 on the street and I want to start the process of restoring it. Serial number is 80262, which I understand puts me in the 48001-and-up (version 3) camp.
I'm getting ready to replace the selenium rectifier with a W04G...
I have previously restored a Sansui AU-717 and a AU-919 and both went well. I must really enjoy removing the notorious Sansui glue because I just purchased an AU-719 from a gentleman in Canada. It looks clean and appears to be all original. It powered up normally and came out of protection. I...
Hello everyone, I'm new to the forum
I recently aquired a pair of original working Infinity Quantum 2 speakers. As far as I know, they have never had any crossover work done.
Both of the Tweeter X-Over Frequency swithces are completely frozen in the HIGH position. I do not want to force them...
I’m still a beginner at electronics repair and this estate-find Pioneer SX-1500T is the oldest unit I’ve worked on. I’ve ordered a recap kit and an LED bulb kit, and with the faceplate off for the bulb install, I want to restore the missing lettering around the Power/Speakers knob and bottom...
It would seem that we have lost some key vintage and substitution parts vendors due to various reasons and I was thinking it might be time for an updated list:
- kpcomponents (Canada)
- webspareparts (Portugal)
- mouser (USA)
- digiKey (USA)
- jotrin (Hong Kong and Mainland Taiwan)
- Moyer...
Hi everyone!
I’m currently restoring a vintage Admiral PWS-E6183AS with Chassis 20A6. I’m doing a full high-end recap using Nichicon KZ and Elna Silmic II.
I’ve hit a bit of a road block with the small "brick-style" capacitors. Specifically, I have 75pF and 10pF caps that have an underline in...
Hi, last year I started restoring the old SA-8100 which belonged to my mother. I changed all the e-caps (including the ltwo large ones 10 mF 50V, half of the diodes, half of the transistors and the relay. The unit works quite well and the improvement has been noticeable, but there are still some...
I have an M-90a imported from Japan that looks like it's spent time in a river with how corroded it is, I got it for cheap so it is what it is, but I'd like to see if I can't fix it. The unit powers on but immediately enters protection mode. I have a step down transformer I'm using to power it...
Hey all,
after having completed a thorough restoration of my Technics SE-9600, now a restoration of my Sansui AU-717 was in order.
I got this amp in working condition, although with a DC offset of ~50mV, a slightly dirty speaker switch and - only detectable with test equipment - a slightly...
Any advice on how to fix this damage or am I just screwed? I've got photos from before it was shipped and it was mint. I'm genuinely gutted.
I imagine it's a veneer, but I also imagine finding a replacement veneer would be borderline impossible. Not to mention the fact I'd probably need to use...
I've got a couple CT-970s showing up from overseas next week, basically the CT-9R but without the complexity of the reverse function. However the CT-970s I picked up are in pretty rough shape with some surface corrosion on the body and tons of grime on the faceplate. I've got no idea what...
Hi all,
I'm refurbishing a Pioneer SX-800 tube receiver. I've done this for several receivers, but this unit seems to have a sizeable number of "composition" resistors.
I'm assuming this is a carbon-composition instead of the plain carbon film resistor. (Correct me if wrong)
I've read that...
I picked up a pair of these M80s recently and they are in need of some work.
The dustcaps on both midrange drivers have almost completely dissolved. I'm a little concerned about how much of that material ended up inside the drivers, but they seem to sound ok.
One of the tweeters is putting...
I restored a Sansui AU-717 last year for another AK'r and was very impressed with the sound quality of the finished unit. I documented this restoration in the thread below:
https://audiokarma.org/forums/index.php?threads/sansui-au-717-restoration-experience.1080560/
In April of last year I...
Hey all,
I recently concluded my restoration project of a Technics SE-9600 - part 1 anyway.
I got this amp (and the SU-9600/ST-9600) a couple of month back. I enjoyed the design and built-quality of the amplifier and everything seemed to be original including original outputs. A couple of...
Hey this is my first post here and my first restoration project as well. I'm hoping to get a little insight on this SA 7500 II I picked up the other day.
This thing was on marketplace for $80 and I couldn't pass it up. I am a huge fan of the old 70s pioneer sound, my dad had one when I was...
Part 1: Random "Popping" Noise
This 771 exhibited random "popping" noise in both channels; measurement of the DC offset at the speaker outputs, demonstrated that the reading would fluctuate widely, reaching at times, several hundred mVs. This behavior was independent of input source and was...
I’ve been restoring a NAD 214 power amp with my 9 yo son for a fun learning project. He’s been doing great with soldering and staying interested. Initial symptoms were: unit powers on, soft clipping light stays on, no relay click. Front lights stayed on even after unplugging the unit suggesting...
Hi all. I've got a previously restored ST-70 that I want to resurrect after a flood a few years back. As you can see, the output transformers and power transformer have some surface rust. The interior, to my eye, looks remarkably well preserved.
My question: what are essentials steps to take...
Hi,
I am restoring a Luxman L560, and I need to find a power switch. Please get in touch with me if you know where to find it.
Also, I need to find a service manual
Hi all!
I have a NIVICO (JVC) 471E-5 that I pulled out of a storage closet in The Rainbow Bar and Grill on the Sunset strip in Hollywood in around 1990
(Along with a pair of Boston Acoustic A70 speakers.)
Thinning out stored posessions in my old age...and decided to get the table and the A70's...